Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi,
We are developing a product (to be produced in small quantities only) that included USB data transfer based on your USB CDC ACM module. We do not have our own USB vendor...
Can an iBasis sim card be activated without being in a device (nRF9160dk or Thingy:91).
I have two sim cards and neither will activate.
Most of the time after entering...
aoa rx hardware: nrf52833DK
aoa tx hardware: my test nrf52833 board
my test nrf52833 board download "direction_finding_connectionless_tx", use " overlay-aoa.conf"
nrf52833DK...
We are currently in the process of looking into the Bluetooth certification as part of a Homekit accessory, and the documentation raised some questions:
the QDID for the...
Hi,
I'm new to ble.
In order to better understand what is going on, on a packet leveI got a packet sniffer.
I found a device that uses a nordic chip, and am trying...
Hi, I am trying to develop an nCS application with serial flash interface, I am using an nRF52833dk & I observed that under the nCS path "v1.8.0\zephyr\drivers\flash" There...
Please guide what changes are to be done for the Light bulb example to be run in 52840 Dongle?
I am using VS Code and built the Build Configuration using the Dongle configuration...
Hello.
I am yoo at korea.
We will connect OLED with QSPI and Driver IC supports SLOWREAD.
- 8bit (Opcode: 0x03) + 24bit (Addr) + 8bit (Read value: Mandatory) + 8bit...
Hello.
I have question for QSPI OPCODE.
According to "nRF52840_PS_V1.5", WREN optional at "the custom Instruction".
- using function: nrf_drv_qspi_cinstr_xfer
...
Hi, I'm trying to use light_lightness example , and button_event_handler didn't work.
Error message is
"multiple definition of "GPIOTE_IRQHandler" "
because I added...
Hi, I'm using nRF52 DK. I'm following tutorial links 1 , 2 and 3 to learn how to add BLE OTA DFU to the example project ble_app_uart.
Step 1
Following the above links...
Dear ,
I am currently testing the UART peripheral on nRF52832 and nRF52840 using nRF Connect SDK.
Basically, I have a sensor that continues sending out data via uart and...
I'm trying to build the pc-ble-driver ( https://github.com/NordicSemiconductor/pc-ble-driver ) to be able to use the nRF52840 as a receiver for a thermometer. See https:/...
I have a custom board with NRF52833 that I'm unable to flash or communicate with using JLinkGDBServer. I was hoping for some help understanding the errors seen in this log...
Hello Nordic team!
I had a post where I verified the answer by misclick: https://devzone.nordicsemi.com/f/nordic-q-a/83749/nrf52-dk-as-central-to-discover-services-on...
