Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi
I want to konw what will softdevice or ble do after the chip enters system on mode.How do I know which components are working during advertise and connection intervals...
I am using the MDBT50Q-1MV2 which has the nRF52840, and have burned the Adafruit Feather Express bootloader using a J-link and the Arduino IDE. The issue is that I have not...
Dear, I need to upload data to w website using nRF5340DK. I decided to use NodeMCU V3, which has ESP8266. The related queires are:
1. How to include and use esp8266 shiled...
Hello !
I'm using USB CDC ACM serial port in interrupt driven mode.
I can see driver operate by 64 bytes chunks.
Linux PC is used as data source and I can see 450KB...
Hello, I am fairly new to programing with nRF52832, Segger Embedded Studio and SDK52 V17.0.2.
I am an EE student, and the majorly of my experience comes from Arduino.
...
Hello,
My setup:
nRF5833 DK, OpenOCD-0.11.0 on Windows 10
I installed the xpac OpenOCD package and attepmted to connect to server using the command
and I get the...
I am using the GNSS Sample in SDK 1.8.99 to test sleep/wake cycles.
The GNSS example is correctly operating in single shot mode by setting the interval to 0. After getting...
Hello, I have the custom design. Schematic is below: I use Visual Studio Code and nRF Connect SDK V1.6.1. My programer is NRF52833DK I used example code (zephyr/samples/basic...
Hi,
We used the nrf52840 in our first release of our project. And we decided to upgrade to the NRF5340. We already have port our software to the Zephyr OS on the nrf52840...
My question is very similar to If I use nrf Connnect SDK 1.6.1 and Zephyr, which Bluetooth QDID should I use?
Following this case I need Zephyr Version 2.2.x and can use...
Hi,
I use CAF leds modules in NCS. After click the button and led lights for 3.6 seconds, I submit power down event when double click button. As show in the following figure...
Hello.
We want to mass programming the nRF9160-SICA in our production IC only - NOT soldered on a PCB.
Is there exist any IC connection adapter for this IC that can...
Hi, Request confirmation that nCS nordic SPIM & SPIS drivers implicitly use DMA, I found the response as in: https://devzone.nordicsemi.com/f/nordic-q-a/83593/zephyr-rtos...
Hello! Does anyone know how to access the source code installed on the nrf52840dongle with the Bluetooth Low Energy application?
As you can see, the application offered...
Hi,
I need to enable PIN based security for my dev. project on Nano 33 BLE, by PIN security I mean force mobile app to enter a hard-coded PIN to connect to my BLE device...
