But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I am running some tests with the long range example provided by Nordic and observed this behavior which I can't account for.
https://devzone.nordicsemi.com/nordic...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi,
I report some problems.
I have been using keil5,it work well. Because nRF Connect SDK doesn't know Keil
now i have used Segger Embedded Studio for a period of time...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
Hi everyone, I implement nrf5_SDK_17.0.2 ble_app_uart example, but when I connect both GND wire and TX wire of the external device to my nRF52840 DK first, my nRF52840 DK...
Hi
As mentioned in this question: https://devzone.nordicsemi.com/f/nordic-q-a/69533/set-tx-power-on-zephyr-device , there is a sample to change the tx power using some HCI...
Hello,
I am trying to use the ble_app_rscs example app into the nRF5_SDK_17.1.0 package for connecting the nRF52840-DK board to the nRFToolbox Android application. However...
I have a small program that is to be used in production to test my device. It has to be scriptable so I'm using teraterm over rtt.
No external IO for a serial port.
Everything...
Hi Nordic,
Can you tell me how to remove commissioned a node from open-Thread ? Basically I want to remove a node from one network and put it in some other network. Are...
Hello,
I encountered a problem while trying to flash my PCA10040 nrf52 development kit.
I am able to compile my code in Segger Embedded Studio without a problem. The chip...
Hello:
I am using an nrf52840 on a custom board with W25Q01NV NOR Flash with the Nordic QSPI-NOR driver. Programming is with NCS v 1.8.0 (upgraded yesterday) and the VS...
Hi Team,
I am developing an application that required SPI communication with msp430.
But, some received characters are disorders, I see them by JLinkRTTViewer logs. For...
Hi
I'm using nRF51822 xxAA (256 Kbyte ROM). My code size are 66 690 byte, I'm using IAR.
Application memory setup:
This means that I have 131 KByte code size for my...
