Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
For my Thingy91 project I need to hook into a variety of hardware interfaces including I2C. I am struggling to relate the pins https://infocenter.nordicsemi.com/topic/ug_thingy91...
Hello,
I'm using the nRF Connect SDK 1.9.1 and I have defined a custom board with nRF52840. This works for normal code (samples, etc).
The .dst has the following structure...
Hi,
Im using PCA10056 nrf52840 to measure light intensity with photodetector.
I got that sensor to measure the intensity of the light on the Arduino. But I don't know...
Hi all,
I have a problem when I try to debug nRF52832 target. The nRF52832 chip is advertising properly but as soon as I enter in debug mode, advertising stops. There is...
We got a project that is using custom boards and custom libraries that is able to compile for one board and that output strange errors for an other. Following is the prj.conf...
Summary: Not able to see messages from printf() statements in the code on the serial monitor.
I'm new to Nordic platform and to Segger Embedded Studio.
I have a Nordic...
Hello,
could you please tell me how to configure the Hardware Chip Select Funtionality for SPIM3. I am developing a communication between a sensor and the NRF via SPI transfers...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
Hi
I want to measure the battery lithium, this battery is the principal source (3.7v 300mh), the maximum voltage is 4.2 when the charge is full,
i'm using this code for...
Hi
I'm trying to enable BLE host-only build on Application core on nrf5340dk, and also enable RPMsg/openAMP.
I'm using Zephyr and its build system.
I get the following...
Hello everyone,
I'm working on a project right now and I want to use the ADS1298 analog to digital converter and configure it with NRF5340dk. Being a beginner I looked for...
hello,
i'm having an nrf52 based system with an antenna switcher in front of it, for antenna diversity. i tried using BT_HCI_OP_READ_RSSI as basis for my antenna diversity...
