Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear,
We enabled QSPI DMA Encryption to cipher the external QSPI communication with enabling NRF_QSPI_HAS_DMA_ENC. So, QSPI DMA communication worked well.
However, when...
Hi,
This might be a simple answer, but I am working a BLE app which I started from the zephyr peripheral example provided in the nrf connect sdk. I removed the cts service...
Hi,
I'm upgrading our RCP firmware that runs on a custom nrf52840 dongle. It was using openthread bare metal on an old version (clone of openthread repo and run make -f...
Hi,
I am develop with nRF5340, ncs1.5.1.
I am puzzled how to read the value of an output GPIO.
I saw the function gpio_pin_get_raw and gpio_port_get_raw, the comment...
Dear Team,
We are developing HID remote with BLE audio feature which support windows platform.
In the NRF52 smart remote 3 BLE audio support only for Ubuntu.
My Queries...
Hi team!
We are working nrFready smart remote 3 with windows 10 pro operating system.
When we paired the given remote (with battery operated) with the windows device via...
Hey all,
I am starting a little research on how to use my NRF51 DK to control a relay in order to turn off/on 220v operating devices.
I dont know much about electronics...
I'm currently working with a client who is implementing the nrf9160 into their product. They had a version of PCB made which connects pins 104-127 to ground, even though the...
Hello,
We need a bluetooth BLE module, for UART communication with AT command.
with certificatation EN300328 V2.2.2. Do you know where we can buy them?
If we use the...
we are using nrf52805 after in few devices sometimes BLE is not visible(stopped broadcasting) to the receiver.
Here are the observation on that faulty device:-
1. Device...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows 10 pro operating system.
we tried to connect this remote with laptop using the...
Hello Devzone,
With an nRF9160 based project and lowest power, lowest current consumption in mind, is there an explicit I/O pin setting to make via Zephyr API for the nRF9160...
Hi
Now I am using NCS1.7.1 for development the nRF52840 chip.I need to use the C standard library(math.h).I set up as follows:
There is no problem when the above macro...
Hi,
I would like to know the functioning of CPFD (I would like to represent the characteristic value as IEEE754 float32) I am not aware of how can I implement this. for...
