Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello,
I want to send 614.4 kHz clock signal to GPIO.
I checked that GPIOTE example could be used for this.
When I update uint32_t cc_value at nrf_drv_timer_extended_compare...
In searching, I haven't been able to find much information on implementing USB CDC ECM. Has anyone successfully implemented CDC-ECM with an nRF52? Alternatively, has anyone...
Dear nRF,
I know this topic has been covered many times, but I am unsure how I can change the uart pins for BLE 2-wire? I have not found any configuration for it inside...
Hi,
We've been in the process of debugging our development board but are having issues. When we try to connect to our board we get:
ERROR: [SeggerBackend] - JLinkARM...
I am using the Segger interface for designing an nRF52 based device. I am planning to use SWDIO SWCLK VTref and GND pins on my device. Is it necessary to connect the nRESET...
Hi!
We upgraded our node version 12.x to v 14.x and are trying to run in on Ubunto. "yarn install" trying to download pc-ble-js driver automaticly from the rebository git...
Hello,
I'm working on getting PSM mode with the Serial LTE Modem on the nRF9160 v1.0.0. The power consumption of the modem (26.4 uA) is too high compared to the documentation...
Hi.
I am using nCS with vscode to develop an application, So far I was only working with peripherals and my build file (.bin) size was about 70kb. Now I want to add BLE...
Hi,
I have a strange question about app_buttons, I have two buttons, only one of the buttons is initialized, which works well, but once both buttons are initialized at the...
Hello,
I am currently trying to include one of nordics flash examples into my project. Ive tried both, flash_fds and storage example. Unfortunately both will assert after...
Hello,
Is it possible to get an example for pc-ble-driver iBeacon detect/scan example.
I see only that one with heart rate, not sure what to modify for iBeacon scan/filtering...
hello everyone ,
i have posted a problem regarding Adding BSEC(bosch sensor ) library using vs code for thingy91 13 day before and i am still begging for help .If Edvin...
I am finding myself seriously lacking in proper explanations of how aspects of the SDK work. For example i am currently trying to gain a full & in-depth understanding of the...
i am compiling sample code for accelerometer from sample C:\Users\mohit\nrf\v1.9.1\zephyr\samples\sensor\adxl362 .
i don't make any changes in code . when i try to build...
