Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Here is the main.c file for AES CTR - /examples/crypto/nrf_crypto/aes/aes_ctr example project
'NORDIC SEMICONDUCTORAES&MAC TEST' is the key
Encrypted hex output: "12 DD...
Hi
I have been struggling with increased power consumption after SPI slave usage, and finally seems to have found a solution, based on errata 89.
However looking through...
Dear all,
With nrf9160, I start GPS function.
at#xgps = 1,1
If GPS positioning is successful, I will receive #XGPSP and $GPGGA information. Though I haven't specified...
I’m new to development with the nRF platform and have a general question on using a SoftDevice. A bit of background: in our application we only need BLE for OTA updates and...
Hello, I've tried a few a few combinations of nrfconnect/sdk-nrf branches, but I can't seem to get `CONFIG_CHIP=y` builds to work.
I'm using the following `prj.conf`:
...
I am using tca9548a to connect 8 IMU sensors with a nrf52832 micro controller. I would like to know how to initialize each channel of the i2c mux and how the control to each...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do Thread DFU
I am following https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee...
Hi I'm developing an application using using PWM+ble_app_uart+libuartes. So I have 2 questions 1. I'm using PWM to ring the buzzer a simple melody. What is the example I should...
Hi,
I have used one of the sample and was playing around a write characteristic. I changed the MTU size to 65 bytes and then tried to send same data from the app to the...
Hi,
I am looking for the solution to the following problem while installing the nRFconnect SDK.
$ west init -m github.com/.../sdk-nrf --mr v1.5.1
FATAL ERROR: already...
Hi,
1. Please help me complete example pca10100e_uart
2.I am testing the nRF52820 UART DFU example
3.The example is named pca10100e_uart based on example pca10040_uart...
Need to create Encrypt Image for nRF5340DK board and used Hello-world sample for beginning.
On Enabling BOOT_ENCRYPT_EC256 Kconfig option, I can not compile Hello-world...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I've tried to debug my application in segger embedded studio, I'm getting "No Bootloader was found" error message...
Hi, I'm building an application include ble_app_uart + libuartes + pwm.I merged successfully two 2 examples ble_app_uart + libuartes into an application. So now I need to...
Hello, everyone.
I learned about Bluetooth communication through the example of ble_app_uart. I learned about Bluetooth communication through the example of bl_app_uart...
