Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Good morning,
I must developped a product with BLE module with nrf52840 chip. The product must comunicated with android product and windows 7, 10 and the product must...
I am using nRF52840 development software based on ble_app_uart_c, and I found that when I set NRF_LOG_DEFAULT_LEVEL as 1, if I download the software by Segger, the device...
I tried using the nRF52 dev kit on Windows for ARM, but it doesn't work, because SEGGER don't provide ARM JLink drivers for Windows, and Windows for ARM doesn't emulate x86...
Hello everyone,
according to the device specification, the nRF52840 can be operated with a MEMS oscillator as LFCLK input, which we intend to do. We plan to use a SiT1552...
I have a Zigbee router app that is mostly based on the light_bulb sample. I have noticed that unlike other Zigbee devices on the network (e.g. Philips Hue bulbs), there is...
I am currently working on a project that involves RSA signing data before POSTing it to a PHP web server.
I believe this uses the CC310 cryptography hardware in the nRF9160...
Is it possible to use ESB over the Bluetooth HCI from the controller, or through its own HCI? Preferably using Zephyr? If not, how hard would it be to implement? I am fine...
Hi
I'm using the nRF Connect Power Profiler UI with the Power Profile Kit II. It works great but has one annoying behavior. When I run the Power Profiler in sampling mode...
Hello,
NCS1.9.1, nRF52840DK, Windows10 X64, VS Code,
i want to use P0.31 as gpio interrupt pin,
anyone know how to do it ?
if config to overlay file like follow...
Hi,
Using the central and peripheral uart samples I have found the following CMake error when trying to increase the MTU ATT to 1020 bytes.
The added lines to the prj...
I am trying to update firmware but I am stuck on steps 6, 7 because I don't know where to get the img_app_bl folder and nrf9160dk_asset_tracker_v2_item_<version-number>.hex...
Hello,
I have developed firmware which communicates to an AWS IoT Core erver. To make sure the device is robust I decided to transmit data every 30s to the server. The network...
Hi,
We have a product which was developed with nRF52810.We found Samsung cellphone M31 couldn't scan the broadcast of nRF52810 with nRF Connect, but ther cellphone could...
I have MCUBOOT compiled under Zephyr 3.0 working fine with my 52840 based project. The transport is the CDC ACM "UART" using CONFIG_MCUBOOT_SERIAL
Using mcumgr.exe to load...
I am now developing nRF52805 with SDK 17.1.0. I am trying to use long pressing to enter the sleeping mode and wake the system up using the short press. However, there is an...
