Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have a product with an nRF9160 and using its modem to connect to a LWM2M server. I have recently enabled modem delta firmware updates, and have seen an annoying issue. The...
Hi,
We want to explore I2C examples in nCS SDK 1.7.1
Can you please enlist all the examples having I2C implementation.
also want to add I'm referring to I2C API's...
Hello everyone!
I am using my nrf9160dk to develop a system that connects to Azure IoT Hub. My firmware code is based on provided azure_iot_hub sample. According to azure_iot_hub...
I 'm using BLE Nordic UART Service (NUS) for streaming data packets which contains read sensor data. I need a way to check the packet loss happening for example if the other...
Hello,
I am developing an application that requires advertising of multiple custom service over BLE. I have successfully implemented the custom services, assigning a custom...
Hi All,
As far as I know , BLE Thrughput is basically set around a few parameters => 1. NRF_SDH_BLE_GAP_DATA_LENGTH
2. NRF_SDH_BLE_GATT_MAX_MTU_SIZE
3. NRF_SDH_BLE_GAP_EVENT_LENGTH...
1) I have set up the Zephyr development environment by following the instructions at https://docs.zephyrproject.org/latest/getting_started/index.html
2) I am able to build...
In my device， I must support HUB(central and peripheral roles) mode. I found it will drop data in weak signal. and It will be better when be central roles only in the same...
Hello.
I am just do one project with Zephyr and nrf52840 to control one step motor, the one task is to get pulse number of pwm pulse when motor is running , I think PPI...
Hello guys,
I'm trying to interface nrf52832 with ds18b20 temperature sensor and I'm using this code https://github.com/sigurdnev/Nordic-DS18B20 and I'm getting the output...
I start a application from the demo central-uart with the NRF CONNECT SDK 1.9.1
I try to communication via the com.
but the first byte of the rx buffer is wrong,I did...
I am running the throughput sample project on sdk 1.9.0 using two nRF5340 dev kits and am getting a throughput of 197 kbps using 2M PHY, Data Length 251 and Interval of 7...
Since upgrading to SDK 17.1.0 i get the following warnings of a redundant redeclaration for SystemCoreClock, SystemInit() and SystemCoreClockUpdate() for nrf52810 and nrf52840...
Hi,
I've installed the nRF Connect SDK, and want to bring up a command-line build environment.
I'm able to do it as it says in the instructions here : Bring up the Toolchain...
How to upgrade the nRF52832 tag in OpenWRT+nRF52832 gateway
gateway(openwrt+nrf52832) |_____ nrf52832 tag1 |_____ nrf52832 tag2 |_____ nrf52832 tag3 |_____ nrf52832 tag4...
