Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
We would like to run our post processing audio enhancement algorithm in the application processor while it is streaming Bluetooth LE audio.
I would like to know the resources...
I think there were a few other cases that had a problem using external flash for littlefs, but I think I found out why it is not working in the latest SDK.
I configured...
I am working on a BLE peripheral FW using 1.9.1 nRF Connect SDK on VS Code.
My application was building uptil now.
I changed one file name. Its .c / .h file names and...
Hi,
I'm using a nrf9160 DK and am wondering how to use the credential storage system. I deleted all credentials for security tag 1, and loaded the root CA pem (not the...
Hi Nordic Community
I am very new to Nordic products and the Zephyr RTOS so please forgive any silly questions.
I am trying to get a better understanding on how to...
Hello !
I’m currently working on a project developed with the NRF52 , and I’m facing a little problem using the DFU function (Device Firmware Upgrade). As shown in the screenshot...
Good day.
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
The spec for the nRF52840 indicates a maximum power level of 8.0 dBm and -51dBm for 2nd order harmonics and -48dBm for 3rd order harmonics. What is the output power level...
Hi,
I need to know. How to put the nrf5340 in sleep mode and how can I woke up the device based on interrupt. Kindly, let me know. How can I achieve this.
Thanks & Regards...
Hello, is it possible to get the altium data from nRF52840 dongle (pca10059.SchDoc and PcbDoc) ? It's so time wasting to clone it from pdf. Thx. Ralf Adler
I followed the document and downloaded nRF Connect for Desktop in Ubuntu 18.04.5.
Then I changed the permission of nrfconnect-3.11.1-x86_64.appimage to "allow executing...
Hello Devzone,
I'm in the development stages on a battery based sensor device, utilizing nRF9160 System in Package for LTE-M connectivity and application processor. I have...
Hello Everyone,
We are using a nRF52810.
We have ran into an issue where our 32MHz XTAL can take longer than 400us and thus the Errata 3.6[68] CLOCK: EVENTS_HFCLKSTARTED...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
I would like to set the radio channel using 'uint32_t nrf_esb_set_rf_channel ( uint32_t channel ) '.
In 'nRF52840 Product Specification v1.7', '6.20.12.2 Operating frequencies...
