Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
NCS1.8.0 Windows10 X64;
spi_loopback test,default code default pins;it is ok.
when i change the SPI_1 pins ，
Failed to achieve the effect, still used the original...
When setting up a pin to toggle on the RTC's TICK event through the PPI and constantly reading the RTC's COUNTER on the nRF52832, my team observed frequent glitches on the...
Hi All!
I am using the cloud client example. The development board is nrf9160. This example works well and sends the message to nrf cloud on button press. Is it possible...
I'm using the Nordic Python libraries to receive the BLE data. I can send the data from our board with the nRF52840 chip on it. If I send the data to my Android phone with...
Hi.
In order to save battery in an "advertising only" peripheral, would it be possible for this module to remain in sleep status and start advertising (for a preset period...
Hi all,
i am using nrf5340 with SDK v1.5.1
I want to know if it is possible to use nrf5340 as central and peripheral device simultaneously?
The application is -
1...
chip : nrf52833 softdevice : s140 nrf52 7.2.0 IDE : IAR OS : windows 10
I try to USB DFU in nrf52833 I'm using secure bootloader base on secure bootloader example and...
I have a project with a nRF9160 and using its LTE modem to connect to a LWM2M server, based on the eclipse Leshan. I am using the lwm2m_rd_client. I have noticed some problems...
I try to integrate mcuboot and BT DFU into my application. I'm using SDK 1.8.0 and DK board nrf52832.
My problem is, that i got this message "Unable to find bootable image...
Hello All,
I am using the nRF52840 DK board. I want to implement OTA in Zephyr. I am a beginner at nordic. Is there any sample example code available to check?
Thanks...
Hello, I need repeatitive timer tick of about 10 seconds either in the while loop or as separate callback function. How to create and initialize a long duration tick timer...
Hi,
In Nrf_SK_for_Thread_and_Zigbee, for openthread mtd, we used to define thread configuration in following code:
So to use node as SED (sleepy end device) we would...
Hi guys, I am fairly new to nRF and I try to understand the ways that data can be displayed to the terminal emulator.
So far, I have noticed that there are four different...
Hello there,
I'm starting out on the nordic platform for the first time but I'm running into an issue. When I try to flash the nRF9160 SiP modem firmware with the latest...
Hello
After building the whole environment of Zephyr and the rest, I downloaded the Serial_LTE_Modem build_nrf9160dk_nrf9160_ns example under Segger IDE to nRF9160 (PCA...
