Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I am trying to include the CMSIS-NN libraries inside the segger project. Since they are not available in the software package inside Segger Embedded Studio, I pulled...
Hello! I've been using Segger Embedded Studio (Nordic Edition) for the project in nRF Connect SDK.
So, this SDK uses CMake to build the projects. But my project involves...
Hello !
I try to understand all available crypto libraries in SDK 17.1.0 what is applicable for nRF52840 and CC310 cryptocell.
https://infocenter.nordicsemi.com/topic...
Hi,
I'm trying to implement a simple FOTA BLE with MCUBOOT following the instructions in the documentation.
I'm using Visual Studio Code NRF extensions as an IDE, and...
I have an early nrf52840-Preview-DK device that has worked fine before. When the project is revisited the board is no longer detected in any of the programs in nrf Connect...
I am building with west and then using this tutorial:
https://docs.zephyrproject.org/2.6.0/samples/subsys/usb/dfu/README.html
to create a .bin file. I then use nrfConnect...
Using NCS 1.8 and NRF5340
Right now I’m able to use the MX25U external flash that we have attached to the nRF5340, We are planning to ship our board with MCUBoot and application...
I am using v7.0.1 S132 SDK on the nRF52832 processor for BlueTooth Light coded in Segger.
I have a high speed output (50uS) to drive an external device using an internal...
My application requires to change the device name as the identification of the device. However, we found the changing the device name might not be detected by the Android...
I successfully used the OpenThread nRF52840 USB dongle support provided by the OpenThread project to implement the radio coprocessor functionality.
However, I had no success...
Hi
I have a strange error in the k_fifo-useage:
Basis is the project peripheral uart
I want to answer on specific commands send via bluetooth
static void bt_receive_cb...
Hi,
I have build the below sample for a nRF52dk-nRF52832 board.
v1.8.0\zephyr\samples\drivers\spi_fujitsu_fram
At compile time I've got this error:
I have followed...
According to Zephyr documentation it is possible to define a thread with K_FOREVER delay so it will not start till k_thread_start is called
https://developer.nordicsemi...
Hi,
i am using a PWM signal to control the brightness of a LED. When the brightness is at zero, i have a random flickering on the LED.
This signal is also present at the...
Hello, i'm using the example ble app uart and I would like to know the maximum data that I cand send to my putty and my phone. Could I have to procedure? I would like to send...
