Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello, i have six buttons on my custom board, these buttons are inited with following code:
(there are pull up resistors present, hence NRF_GPIO_PIN_NOPULL is used)
SEGGER_RTT_printf...
Hello,
We are using nRF52840 chip for a power-sensitive application.
We use the UART which is connected to a LoRaWAN module.
Now when I enter the system ON mode after...
Hi,
I just started working with Zephyr and having some problems right out of the gate.
Board: Nordic nRF52840DK Example: i2c/spi_fujitsu_fram Branch: Main
When I'm using...
Can Nordic team be sure that SweynTooth test team has tested Nordic chips? If so, the claim in Nordic dev zone that Nordic chips are not listed indicating Nordic chips are...
I have followed Einar's response on the below thread but I still cannot see the logs on the SES
https://devzone.nordicsemi.com/f/nordic-q-a/79682/adding-mcuboot-bootloader...
Hey devs,
I'm trying to get the i2c interface to work with the MP8862. I followed the TWIS driver guide to get started and in there everything worked.
Now I wanted to...
Hi Everyone,
I'm using VS Code, nrfConnect SDK v1.7.0
I'm trying for minimal bluetooth roles(either central/peripheral) along dfu support in nrf52820 chipset.
when I...
Hello,
I recognized a wrong answer is sent by the ZigBee stack of nRF Connect 1.5.1 and 1.7.0 (and others).
Eg. the application provides a color control cluster as a...
Hello.
It is developed using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I am implementing the advertisement processing, but the advertisement stops when...
Hello,
I compiled pc-ble-driver from github and it when i debug heart_rate_collector in adv_report_parse function i only get 1, 10, 255 field_type and never BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME...
Hi,
I am trying to erase and flash a nRF52840 chip on a custom board. I use a J-Link EDUwith the Cortex M adapter to plug onto the board. I checked the hardware conf several...
I am using libuartes example. I only use send_UART (char*sdata, int len) in main before while (true) or in void uart_event_handler(void *context, nrf_libuarte_async_evt_t...
I'd like to use Power Profiler to measure really low currents (watches) ~0.4 microAmps.
However, Power Profiler II measures 1.5microAmps even when disconnected with or without...
Hello,
Have anyone knowledge on how to force to include, using nRFSDK, the AdvA field in the Ext Hdr of a BT 5 long range advertisement primary packet frame ?
We are testing...
