Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
I want to konw what will softdevice or ble do after the chip enters system on mode.How do I know which components are working during advertise and connection intervals...
I am using the MDBT50Q-1MV2 which has the nRF52840, and have burned the Adafruit Feather Express bootloader using a J-link and the Arduino IDE. The issue is that I have not...
Dear, I need to upload data to w website using nRF5340DK. I decided to use NodeMCU V3, which has ESP8266. The related queires are:
1. How to include and use esp8266 shiled...
Hello !
I'm using USB CDC ACM serial port in interrupt driven mode.
I can see driver operate by 64 bytes chunks.
Linux PC is used as data source and I can see 450KB...
Hello, I am fairly new to programing with nRF52832, Segger Embedded Studio and SDK52 V17.0.2.
I am an EE student, and the majorly of my experience comes from Arduino.
...
Hello,
My setup:
nRF5833 DK, OpenOCD-0.11.0 on Windows 10
I installed the xpac OpenOCD package and attepmted to connect to server using the command
and I get the...
I am using the GNSS Sample in SDK 1.8.99 to test sleep/wake cycles.
The GNSS example is correctly operating in single shot mode by setting the interval to 0. After getting...
Hello, I have the custom design. Schematic is below: I use Visual Studio Code and nRF Connect SDK V1.6.1. My programer is NRF52833DK I used example code (zephyr/samples/basic...
Hi,
We used the nrf52840 in our first release of our project. And we decided to upgrade to the NRF5340. We already have port our software to the Zephyr OS on the nrf52840...
My question is very similar to If I use nrf Connnect SDK 1.6.1 and Zephyr, which Bluetooth QDID should I use?
Following this case I need Zephyr Version 2.2.x and can use...
Hi,
I use CAF leds modules in NCS. After click the button and led lights for 3.6 seconds, I submit power down event when double click button. As show in the following figure...
Hello.
We want to mass programming the nRF9160-SICA in our production IC only - NOT soldered on a PCB.
Is there exist any IC connection adapter for this IC that can...
Hi, Request confirmation that nCS nordic SPIM & SPIS drivers implicitly use DMA, I found the response as in: https://devzone.nordicsemi.com/f/nordic-q-a/83593/zephyr-rtos...
Hello! Does anyone know how to access the source code installed on the nrf52840dongle with the Bluetooth Low Energy application?
As you can see, the application offered...
Hi,
I need to enable PIN based security for my dev. project on Nano 33 BLE, by PIN security I mean force mobile app to enter a hard-coded PIN to connect to my BLE device...
