Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Dear, I created a project in SES. I modified the zypher.dts file to define some pins as below:
1. I added some pins in aliases as shown in fig 1.
2. I added pins with...
Hi,
nRF Connect SDK1.8.0, Windows10 X64.
as follow simple code，it will infinite restart.
but all short change to int or char, it work well.
the same code, run...
Hello
Happy Christmas in advance.
I meet a trouble about using littlefs and mcuboot at nrf52840dk.
ncs1.7.1
project:littlefs
I have changed the nrf52840dk_nrf52840...
Hi all
I'm developing a BLE application using nRF52832 : SDK 17.xx
I need to embed a passkey, and the only app example relevant in this case is ble_app_gls.
using this...
Hello again Nordic World,
I am using a slightly modified version of the ble_central example running on both 10028 and 10040 boards as "test central boards" for communicating...
Hi,
We are developing trainer sensor device and looks very smooth so far. But our questions is some apps change our device name to Bryton Trainer xx in the searching stage...
Hi there,
Having just migrated from an x86 Mac to an M1 Mac, I'm now having difficulty getting the programmer app of nRF Connect for Desktop to detect a device. When I attempt...
1) what is the touch pad IC driver that will support nRF52840 ?
2) S25FL512s compactible with nRF52840 as an external nor flash interface . if yes how to get started with...
I am using nRF Sniffer/Wireshark to diagnose some problems with a custom app using 128 bit Service UUIDs as well as well known 16-bit UUIDs.
In the screenshot below, you...
Hi,
Based on previous threads on the matter:
https://devzone.nordicsemi.com/f/nordic-q-a/46565/sdk-15-3-0-missing-bootloader-definitions-for-nrf52832_xxab-qfab
https...
HI
We are using nrf connect sdk.
We understand that when we put the nrf in power down and if any interrupt comes in any gpio than it will reset and wake up.
But my question...
Hello everyone,
im quite new to nrf52.
i m trying to fecth the ADC value on teraterm. but it is not showing the expected output.
please help..
thanx in advance.
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
While developing a set of C++ tools to simplify configuring and managing BLE on NRF52 chips, I've encountered an error code returned from the advertising module's ble_advertising_start...
