Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hi,
I build the smp_svr sample for nrf52dk_nrf52832. I installed Go on my windows machine and I am able to run the mcumgr tool. When connecting Teraterm to the UART of my...
Even if i did the configurations i got this error because of the manifesting stage.
When i did the configurations which is like below,
west config manifest.group-filter...
Hello,
I am trying to use Direct Test Mode example on SDK v17.0.1 to do our product's pre-production RF tests. I can see expected results on nRF Connect Direct Test Mode...
Hi, While testing the new nrf5340 Audio DK and BIS example, I wanted to see how the Periodic Advertising Sync Transfer (PAST) data looks on the nRF Sniffer version 4.1.0....
Hello,
I want to know to which pin should i rely my AMPERMETER so i can measure the current consumption of the µC .
If you have other hardware solution to measure the...
Hello,
I am trying to flash a Sparkfun thing plus nrf9160 board but I am not able to for some reason.
This is what I am getting on the logs when trying to select the...
Hi all! I'm new to mesh bluetooth technology and I'm stuck with some bugs.
I am using the development boards nrf52dk and my goal is to create a network of about 6 nodes...
I am using nRF5 SDK version 17.1.0 and am seeing this line in file examples/ble_peripheral/ble_app_uart/pca10040/s132/ses/flash_placement.xml
<ProgramSection alignment=...
Hi, I am trying to transmit data via Bluetooth from two sensors at the same time to a dongle that will send the data to the computer via USB, I am able to connect the two...
Hello,
I'm doing some current measurements on both the Thingy91 and the nRF9160DK and I'm seeing some weird behaviours. My setup is as follows:
First measure on the nRF9160DK...
Hi dear reader
I've read several threads on this issue, but none of them could help resolve my problem.
I've an application which currently is only starting some advertising...
Hi
I am looking for an advise about selection of the optimal connection parameters. I am using couple of nrf52832 devices as the nus peripherial. As the central device I...
Dear colleagues,
I'd be very grateful for your help in the following challenge: I would need to change pins and/or i2c bus speed without recompilation of my code.
I can...
Hi,
I am following the NRF5 getting started guide. Unfotunately, I am falling down at the first hurdle. When copying the .hex to the JLINK storage, a fail.txt is generated...
