I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi there,
I have a problem to implement the SPIM in the Network core. I cannot detect any signal from SPI_SCK & SPI_MOSI by oscilloscope and logic analyzer (no signal from...
Hi,
I'm using VS Code to develop an application based on the Zephyr iso_broadcast sample.
How do you edit prj.conf? If I select prj.conf in the Explorer pane, then click...
Does the nRF52840 support Bluetooth low energy power control? I am using raspberry pi, running Raspian, kernel version 5.15.30 and I am specifically referring to the product...
Hi support team:
I develop my project with sdk 15.2.0 on nrf52832. Now I met a situation that I might need to call app_timer_start() again before the same timer is timeout...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
Hi! I'm trying to understand how my board is working. I think that the Arm Trustzoned provides the possibility to the board to have two domains, one secure and one non-secure...
Hello,
NCS1.9.1, two nRF21540DK, Windows10 X64, VS Code,
periodic_adv and periodic_sync , only 3M distance can recv data,
if over 3m, will unstable reception / disordered...
Hi,
I am on nrfConnect SDK v1.7.0, with a nrf52832, with UART in ASYNC mode.
During the uart event callback, the event type UART_RX_STOPPED, but when I check for the error...
Hi,
Hello,
I am working on TM4C129XNZAD microcontroller, from that everything working fine like no error no warning and If I flash the code also its programming and the...
I've mostly gotten the tools installed to build for the SparkFun Thing+ nRF9160 board. It had a version of the at_client installed, in that it responded to some AT commands...
Hi
I am testing POF function on 52832 based on SDK14.2 and SDK17.0. And test project is SDK example ble_app_beacon.
Code as show:
#include "nrf_drv_power.h" static void...
Hello all,
I'm currently working on an evaluation of a AoA location system. For that I'm making use of the Nordivc 12 Array Antenna, and two nRF52833 DK (one connected to...
Hi, I'm facing an weird problem when I use an function that is contain while loop
When I uncommented the 35th line => call GPS_init_usingWhile(GPS_RMC,RMC_response); ...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
