Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
In order to protect my device from becoming bricked when APP and NET side implementation of RPC application differs, due to wrong version being flashed or OTA fails on one...
hi:
Use the https_client routine to send data after the socket is established, and then send the data after getting the response. The errno returns as 128, which can confirm...
hello Nordic
i am working with nrf52832, with zephyr, ncs v1.7.1,
the device has a sensor that sample at 26khz each sample is 3 channels of 2 bytes data. the sensor use...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Hello,
I work with NRF52832 evaluation board.
SDK 17.1.0
I try to implémente DFU -> pca10040_s132_ble / pca10040_s132_ble_debug.
Applicatif is : ble_app_buttonless_dfu...
Hi,
I'd like to implement Keil RTX5 on my custom BLE project for the nRF52832 using the S112 SoftDevice v7.2.0.
We are looking to standardise as many of our projects as...
In my schematic design, my nrf5340 uses vddh power supply mode, and the output VDD does not mount any load. Is it necessary for me to connect each VDD pin together during...
I am a user developing using nrf52832. I have a question about TX POWER. TX POWER can be set to -40, -20, -16, -12, -8, -4, 0, 3, 4 by using sd_ble_gap_tx_power_set(). I tried...
When I use two nrf5340 audio DK to test the LE audio demo, the handset side always crashes. Especially when I move the DK that is used as the handset.I think that incomplete...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
I'm using NCS 1.9.1 and Segger SES
Following Nordic's recommendation I first made a copy of BLE/peripheral_uart in order to preserve the original code and then used the...
Hello, I have a question.
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral.
I have a question about the output time of the advertisements. The...
Hi Nordic ,
My product is working fine but i'm focusing on improving consumption at maximum because it is working on small battery ( evoluated tpms application)
It uses...
Hi everyone!
Could anyone clarify a few questions regarding channel mapping?
1. Is that true if I want to use specific BLE channels I need to do it just once on a central...
