Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
When using nRF Connect SDK v1.6.1, a BLE peripheral that supports 2 simultaneous connections could be created by including these lines in prj.conf. These lines set the Link...
Hi,
this is kind of continuation of my previous ticket . After solving it the last time I thought that I don't need wait_for_flash_ready() function as it caused some problems...
I just buy nRF5340.
I install nRF Connect in my PC.
and install bluetooth app.
I just select my pdk.
log show
INFO Connected to device with serial number: 000960119975...
Hi,
I have the following 2 scenarios:
Scenario 1: I create an image with nrfutil containing SD, App and debug bootloader. I flash this image and it works. Then I change...
We have nrf5340pdk kit we are trying to flash code via nrf connect or Segger studio but firmware is not flash and when we powered up the pdk it's showing three port can you...
I'm using Visual Studio 1.7.1 on Windows 10 machine. With an nrf916DK.
I'm trying to learn about the shell and all seems to be working fine, based on what I've found in...
I'm trying to work with Kismet's nrf51822 plugin that would allow kismet to read the nRF BLE sniffer 4.1.0 the same way Wireshark does. Alas, theirs is C based and I don't...
Dear friend,
Based on the following conditions: SDK: 15.3 Target board: nRF52840-DK Example: \examples\ble_peripheral\ble_app_ancs_c ios version: 12.5.5 Do the following...
Hello,
I have successfully achieved the modem delta firmware update from mfw_nrf9160_1.2.7 to mfw_nrf9160_1.2.7-FOTA-TEST, vice-versa with sample code. But when it comes...
Dear support
Just started to learning following the tutorial here - https://devzone.nordicsemi.com/nordic/b/archives/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-3-0#h769sk6kqovea15p99jn16lstat1dtpuuw...
Recently I purchased nRF9160 DK and I have a Vodafone Idea SIM (active). I followed the instructions precisely as per the Nordic infocenter but I am not able to connect my...
Hello
nRF52840 is easy to know pin number,
but nRF5340 no pin map,i can't read the pin diagram.
don't know where the pin corresponds to.
thanks
Best R...
Hi,
I managed to have the fat_fs sample to work.
Now i would like to be able to write and read files, onto the SD-CARD, that a PC will understand, it seems to needs...
Hello all,
I am developing on the nrf52 dk. and the following type definitions should be defined according to the given library.
Would somebody please comment if that...
