Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
hi,
How can I access flash memory of nRF52840 while using softdevice ? I just want to read and update two integer values? is there any simple way to do this?
Thank you...
Hi all:
I want to dynamically change device_name at peripheral_hids_mouse,
I perform two tests, but they are all not successful.
(1)
add below command into prj.conf...
Hello,
I am attempting to configure a Raspberry Pi as an OpenThread router, using the nRF52840DK for the RCP. Everything built fine. When the Raspberry Pi boots the avahi...
Hello,
I want to measure the frequency of 32.768k X'tal accurately.
I was able to output an external 32.768k X'tal to GPIO on a different CPU. Is there such a way with...
Hi Nordic people,
I've been working with the s140 for a long time now, having applications with our own central and peripheral device, but so far, the only way to make sure...
I followed the instructions to downgrade the desktop application and add the URL for the older tools. Installed the 3.7 compatible BLE app and get the error below.
I finally got a working i2c code base but it seems that the nrf9160 has internal pullups on the i2C bus me trying to combine this with a TXS0108 causes weird issues. I suspect...
Dear Nordic Engineer
Our costomer has developed a keyboard using LLPM in NCS.Now Now they have encountered some problems.We have been working with them for a long time but...
Hi. I am returning to developing on Nordic devices after some time away, enticed back by nrfConnect / VSCode support for MacOS. I am running MacOs Monterey 12.1 and I have...
The dumped stack information (especially the PC) point to what was running when the WD fired. This makes sense to me, but conflicts with the advice posted in the question...
Hello Nordic, Our procurement team is worried that the nRF52832 has reached end of life. I wanted to confirm if this is the case? If this is not the case, when is it expected...
Hi, community.
From the official document, I have learned how network core Bootloader works.
It can write data from shared SRAM to the corresponding flash address of Nework...
Hello,
i'm programing a nrf52832 and a nrf52805 and I'm using the peripheral uart example, I would like to change the size of the bytes of my rx and tx that I can send...
Hi
I have a board nRF52840 configured with some QSPI with filesystem configured
I would like to manage the file system from an app and I saw that - nRF Connect Device...
I'm working on a project where we need to store into FLASH about 1350 bytes of compressed data at about 2HZ (twice a second). This is my first Nordic/Zephyr project, so I...
