Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
Is there any way that a BLE event handler installed with NRF_SDH_BLE_OBSERVER, can stop the execution of other (following) observers?
I have various modules using their...
Hi
I am a student and this is my first project working on BLE. Please keep that in mind.
The end goal is to create a fingerprinting system with a Thingy (nRF6936) as...
I have modified the BLE app Blinky example so that the LED is enabled (state 1) on power up. However, this is not being reflected on the BLE side because when I connect with...
Hi, when debugging, I'm encountering this problem where relevant SPI registers (likely status registers) signaled a successful read before the actual data could be pulled...
We're developing a mobile application which will communicate with a satellite antenna over BLE. We will not have access to the antenna for a few months, and therefore we aquired...
I am using the UART to perform serial DFU on nRF52832. I got it to work fine using nRF Connect SDK 1.8.0.
Now, I need to pass some serial data to the APP when not in DFU...
Hi, I have to develop a new nRF5340/Zephyr/MCUBoot-based device that communicates with a Windows application via USB. The Windows application already manages other legacy...
Hello,
I'm trying to implement a set up of the ble device name from the NVMC UICR register.
But when I try to take it from the register and to set it has a name, it doesn...
Hi,
when using the spi peripheral in slave configuration, what can I expect at power consumption level? does the spi peripheral derive its clock from an internal system...
Hello,
I am using nRF52840 DK's P20 SWD to communicate with an external nRF52840 board . My setup works fine with nrfjprog running from command line. To communicate with...
Is there any example code using a QSPI image as the input for the bootloader instead of e.g. BLE? What format does that have to be in to begin with? Currently doing DFU updates...
Hello friends
I am fresher for Nordic semiconductor . I want to interface triaxial accelerometer of 15MHZ frequency with nrf52840 with inbuilt ADC and transmit the data...
Hello,
I will try to use the macro ZB_ZCL_SET_MODIFY_ATTR_VALUE_CB to define a callback when an attribut is written in my device. But the callback I write is never called...
I had a look on APIs to use UART in Zephyr in the link https://docs.zephyrproject.org/latest/reference/peripherals/uart.html#uart-interrupt-api . There are three types: Poll...
