Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I've tested two scenarios using a hardware loopback to test UART functionality. The double buffer approach does not work as expected.
SDK version 1.6.1
CONFIG_SERIAL=y...
Hi,
I used nRF91DK for almost 2 months non stop to debug the final nRF91 based board for our air quality monitoring hardware to fight the propagation of Covid virus.
But...
I tested various copy methods in terms of instruction cycles, that I determined with DWT.
For that I copied an uint8_t array size 70 by
for Loop --> 63 Cycles
memcpy...
Hello,
I am using nRF52840 dev kit with sdk 17.0.2, s140 softdevice and dfu bootloader also implemented.
When I download the firmware to dev kit it works as intended...
Hi,
i am working on nRF52832. i am facing a issue of RESET when i call advertise_start() again after advertise duration. in debug it shows fatal error.
Hi there,
I've installed and followed the nRF Connect SDK manual install getting started guide ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing...
I'm using 52832 as a Central(SDK_17.0.2/S132_7.0.2), and sometimes get a connect-disconnect failure with reason 0x3e.It happens randomly and frequently.
I search the forum...
Hi Supportteam,
i am trying to use Release Assistance Indication (RAI) to shorten the RRC-Connected using nRF9160 DK.
I'm enabling REL14FEAT with the following AT commands...
Hello, sir.
I used to work on twi0 and twi1, but now I'd want to shift both twim0 and twim1. However, I'm getting an error saying that 'NRFX TWIM1 INST IDX' is undeclared...
Is it possible for nRF Connect iOS app to display devices that were connected/paired through the iOS Settings menu? The problem I am having is when looking to perform DFU...
Hi iBasis support,
I'm having a billing issue with your website. I'm using the iBasis card with the NRF9160DK board.
When I ran out of data, I just follow the link on...
Right now I use the app_timer_cnt_get() method to get a current tick count. It appears to return a counter that increases with 32768 counts per second. However, it overflows...
Hi,
In NRF52832 i have integrated IMU sensor and and DPS sensor . i have build code and Run .
But after 2-3 minutes its stucked . so then i pressed the pause button ....
