I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
Hello,
My name is Edward, I am trying to configure a net Thread with auto selection channel, do you have any example about this?
I have based my development on the simple_coap_server...
In the SDK ble_gatt_db.h file the ble_gatt_db_srv_t struct has a member misspelled as "charateristics" rather than characteristics. Was that done on purpose?
Hi,
I would like to resume the discussion made a few days ago in this post.
Is it possible to hide some BLE services until the connection is successful? I want only my...
I'm just starting... I have a little programing experience and knowledge of electronics
My project is controlling stepper motors over ZigBee using cell phone.
I have Samsung...
I have an application where I need to periodically write a few KB of data from my nRF to a host computer. Since TXD.MAXCNT tops out at 255 bytes, I'm trying to set up all...
Hi. I am trying to add a RTC to my ble project. I copied all the simple code from the RTC example, and set all the sdk_config.h settings to match.
As per usual millions...
Looking to permanently change UICR REGOUT0 to 5 for 3V3 on VDDOUT from dongle, to power a small Pulse Oximeter. Then using nRF Connect SDK and Zephyr, get Bluetooth GATT services...
Hi,
As a newbee :-)
Im trying on an nRf5340DK board. I use NRF-connect/Vusial Studio Code: I managed to use zephyr/samples/basic/bkinky example with a build in nrf3540dk_nrf5340_cpuapp...
I erased a board using a MAC (Monterey 12.1) and a Segger Version 11.0 Part-no 8.19.28
nrfjprog --masserase
After which I was no longer able to program, connect, or recover...
Hi,
I was wondering if it was possible to avoid JWT for the NRF9160 by establishing connection between an MQTT Bridge to Google Cloud. Our goal is to establish 24/7 connection...
Hi NRF folk,
when I build sample projects in VSCode (ncs1.8) it works only for some projects (zephyr_st_ble, zephyr_system_off,...). When I use any of the sensor project...
I am using nrf52840-DK and trying to get the Zigbee Switch working. This is just a plain zigbee switch with no bind to light. However, this set attribute during init results...
Hello,
I am trying to make an application with three dongles and one DK. This application consist on control the 4 LEDS of the DK, and each LED is controlled by one different...
I have encountered two issues while using the NRF PWM driver on the nRF52 DK, with or without SoftDevice S132, along with SDK v11.0.0
The first one is the use of the NRF_DRV_PWM_PIN_INVERTED...
