I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
I'm building a COAP client using the Nordic nRF9160DK cloud coap-client example code as my base. I have the UDP version working great. But I'd like to convert to TCP.. I was...
Hi all, I have an odd issue with an iphone XR. The NRF Connect for Mobile application can see adverts from the device when scanning, but the device does not appear in the...
Hey! I'm trying to sniff the data moving between a Bluetooth LE button and a Central.
Installation of the Bluetooth LE Sniffer went pretty smoothly but Wireshark only shows...
Hi,
I'm trying to use a nrf delay to make a delay for a motor. The idea is to make the motor oscillated by putting it forward and then reverse via a delay. (you can find...
Hello,
I need to run "west build" and "west flash" commands from my custom IDE/Editor. If I open up Toolchain Manager and then do "Open bash" or "Open Command Prompt", ...
Hello,
I am trying to do directed advertising while us ing the coded PHY whithout bonding the devices but i am running into some problems.
The device with the BT-address...
Hi,
I use nRF5340DK (0.11.0) as HCI controller and noticed it can randomly (?) accept PDUs with access address other than configured. This basically makes it impossible...
Hi,
When I build CLI sample in nRF_Connect_SDK, I don't get any USB port for CLI.
I believe the sample is in default mode built for UART.
How to build this for USB,...
Hello. I can't normally use USB for two-way communication.
The problem is sending the PRX payload in ACK packets.
After conducting a simple test: PPTX sends a packet once...
Trying to use the basic baremetal mode as my application is very simple and dont want to go through RTOS stuff.
I tried with Timer and RTC, both case if I enable the interrupt...
Dear Nordic Team,
I was trying to use the I2C peripheral on the nRF5340 with clock speed of 1MHz, but I kept getting the error "unsupported speed". I was using the function...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
I am using the nRF 52840dk board and I am new to nRF, I had worked on Cypress CYBLE & CYBT-343026-01. I am starting my development for basic BLE transmit, eventually, I am...
Dear Nordic experts, How do you verify that a (mesh) firmware has an app key assigned? What I'm looking for is basically the Mesh SDK's version of NCS's bt_mesh_app_key_exists...
I used the alternate method of installing nRF connect described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.8.0/nrf/gs_installing.html#build-environment...
