Hi,
I am just evaluating the nrF5340 for an audio bluetooth project. I am trying to find out if the nrf5340 can receive bluetooth audio (classic or LE) from one device and...
Hi,
I am just evaluating the nrF5340 for an audio bluetooth project. I am trying to find out if the nrf5340 can receive bluetooth audio (classic or LE) from one device and...
Hi,
I am just evaluating the nrF5340 for an audio bluetooth project. I am trying to find out if the nrf5340 can receive bluetooth audio (classic or LE) from one device and...
Hi,
We have onboarded several hundred nrRF9151 devices using the nRF Cloud "bulk onboard" UI (preconnect onboarding using device_credentials_installer.py ). Generally, this...
Hi there,
I would like to add some extra data to mesh-nodes, when not provisioned -- with ble_advdata_manuf_data_t usage. What is the best way to do it and where?
And...
Hello,
I need to use Port 1 pin 8 as an interrupt pin:
This results in the error NRF_ERROR_INVALID_STATE, when nrf_drv_gpiote_in_init() is called. Everything works fine...
Hi devzone, I've had UART communication problems between nRF52 and a BG96 modem for a long time.
today I added a pull down resistance on the rx of the nRF52 and it works...
Hello I'm trying to get the lower consumption with this EvK in power off mode. I was expecting around 0.5uA but the minimum I get is 1.8uA ~ 2uA.
The measure has been done...
Dear All
I tried to connect to an apple device, it is successful but soon after that, it is disconnected with reason code 0x13 - terminated by remote user, I tried to change...
Good day,
I am currently developing with two NRF52840 DK boards, and I also have two NRF Dongles. On a dongle a sniffer for ZigBee. I am working with SDK 3.2. This is my...
Hi i want to make a low power delay ms (blocking) function for nrf52805 without softdevice and without NRFx, just writing to the registers.
The RTC1 events_tick never...
What is the recommended way to do DFU over Mesh in Zephyr? I saw DFU documentation in nRF5 SDK for Mesh v5.0.0 but not sure how this relates to Zephyr
Can you point me to...
Hi,
I'm running a custom nRF52811 rev1 connected to a Quectel BC660K. I'm getting this error on RTT:
Here's the initialization:
And the uart event handler:
src...
Hi Nordic Community
I have been building a thermometer device from which I would like to send temperature values via periodic advertising.
I have based the sender and...
Development setup:
2 x nRF52840 SoC
Our own PCB’s with inverted F-antenna
LE PHY 1M
nRF Connect SDK v1.8.0
Hi,
During testing we experience an issue which...
Dear Sirs.
I bought thing91 and nrf9160.
I have connected the thingy 91 with nrf9160dk with prog/debug cable but I dont able to debug the application on the thingy91....
Hello,
I am using SES Nordic Edition v5.60 and I would like to be able to include pre-processor directives in my project but I could not find the pre-processor optins. ...
Hello, im trying to send Data from one Devkit to another (nrf9160 from nrf52840) the Problem is that if i enable Bluetooth on the nRF52 i get an error when receving/transmitting...
Hi, I am using nrf52840, SDK v17, SES v5.10 ble_app_uart example for the development.
I am able to send data from the nrfConnect app to uart but not more 1 byte at a time...
Hi,
I have this development board https://www.nordicsemi.com/Products/Development-hardware/nRF9160-DK . I would like to use development board as nb-IOT modem and other MCU...
