• State Verified Answer
  • Locked Locked
  • Replies 7 replies
  • Subscribers 24 subscribers
  • Views 633 views
  • Users 0 members are here
Attachments (4) Download All
Nordic Case Info
  • Case ID: 281305
Options
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

nRFConnect SDK Sample not working (periodic_adv _sync)

user106325

Hi,

nRFConnect SDK Sample not working (periodic_adv _sync)

I have two nRF52840 DK with nRFConnect SDK 1.7.1

Compiled and run on nRF52840 boards:

   \ncs1.7.1\zephyr\samples\bluetooth\periodic_adv

   \ncs1.7.1\zephyr\samples\bluetooth\periodic_sync

i've only changed prink to BT_INFO.

I found that in the periodic_adv,

   mfg_data[2]++;

is sent with the advertisements, but it is not received at periodic_sync:

The debug run printout :

 [DEVICE]: 21:B6:31:15:B8:3C (random), AD evt type 5, Tx Pwr: 127, RSSI -53 PerAdv C:0 S:0 D:0 SR:0 E:1 Prim: LE 1M, Secn: LE 2M, Interval: 0x0000 (0 ms), SID: 0

In the periodic_sync, function void scan_recv ()

    if (!per_adv_found && info->interval) {
        per_adv_found = true;

        per_sid = info->sid;
        bt_addr_le_copy(&per_addr, info->addr);

        k_sem_give(&sem_per_adv);
    }

info->interval always 0.

And  callbacks     sync_cb,    recv_cb  are never called.

Did I miss anything?

thank a lot.

maybe I can't use Wireshark-win64

Parents
  • +1

    Hello,

    When the Sniffer is not showing up as an interface in Wireshark it usually because the Python version invoked by Wireshark is missing the PySerial dependency. Maybe you have several versions of python installed?

    Either way, please check the log.txt file in %APPDATA%/Nordic Nordic Semiconductor/Sniffer/logs for errors. It may help us confirm what the problem is.

    Best regards,

    Vidar

  • 0 in reply to user4240

    Hello,Vidar Berg,   i'm sorry.

    Please ignore my previous reply，I've found log.txt,  and capture the le data.

    but  callbacks  sync_cb,recv_cb  are never called.

    thank a lot.

  • 0 in reply to user106325

    Hello,

    The log shows that you are using the Softdevice link layer even though CONFIG_BT_LL_SW_SPLIT=y is set in your project config. Maybe you need to reload the project for this change to take effect?

    As you might now, the Softdevice LL did not support periodic advertising in v1.7.x (experimental support introduced in v1.8.0).

    Log output with Zephyr controller and SDK v1.8.0:

  • 0 in reply to user4240

    i've change to ncs1.8.0, i see your picture， My version is different from yours.

    why my Bluetooth controller Version is 223 and HCI/LMP version is 5.2?

    Is there a problem? Does it need to be upgraded？if need how to upgrade?

    thanks.

  • 0 in reply to user106325

    Please try the hex files I built below. The only change I made was to enable the Zephyr LL controller by adding CONFIG_BT_LL_SW_SPLIT=y to the project config files. Logging is enabled over UART.

    Hex and .conf files:

    Log output:

Reply Children
No Data
Related
Terms of service