Hello,
I am trying to work with the MCUBoot bootloader in my project. I was able to configure and build my project and it appears to run properly when I flash it to the chip directly. However when I try to debug it I get the following error:
Run to 'main' timed out. Trying to pause program
The full debug console output was as follows:
Launching gdb-server: "C:\\Program Files (x86)\\SEGGER\\JLink\\JLinkGDBServerCL.exe" -singlerun -nogui -if swd -port 50000 -swoport 50001 -telnetport 50002 -device nRF52832_xxAA -select usb=682211915 -rtos "C:\\Program Files (x86)\\SEGGER\\JLink\\GDBServer\\RTOSPlugin_Zephyr.dll"
Please check TERMINAL tab (gdb-server) for output from C:\Program Files (x86)\SEGGER\JLink\JLinkGDBServerCL.exe
Finished reading symbols from objdump: Time: 63 ms
Finished reading symbols from nm: Time: 60 ms
Reading symbols from c:\Soberlink\soberlink_sfw\trunk_NordicBLE\SL_Connect_ST\build_connect\zephyr\merged.hex...
(No debugging symbols found in c:\Soberlink\soberlink_sfw\trunk_NordicBLE\SL_Connect_ST\build_connect\zephyr\merged.hex)
WARNING: Cortex-Debug will deprecate use of GDB version 8 after July 2022. Please upgrade to version 9+
0x0002e6a2 in ?? ()
Program stopped, probably due to a reset and/or halt issued by debugger
add symbol table from file "c:/Soberlink/soberlink_sfw/trunk_NordicBLE/SL_Connect_ST/build_connect/zephyr/zephyr.elf"
(y or n) [answered Y; input not from terminal]
Reading symbols from c:/Soberlink/soberlink_sfw/trunk_NordicBLE/SL_Connect_ST/build_connect/zephyr/zephyr.elf...
add symbol table from file "c:/Soberlink/soberlink_sfw/trunk_NordicBLE/SL_Connect_ST/build_connect/mcuboot/zephyr/zephyr.elf"
(y or n) [answered Y; input not from terminal]
Reading symbols from c:/Soberlink/soberlink_sfw/trunk_NordicBLE/SL_Connect_ST/build_connect/mcuboot/zephyr/zephyr.elf...
2 Resetting target
[New Thread 536878408]
[New Thread 536877856]
[Switching to Thread 536878408]
Reading symbols from c:\nordicsemi\v1.9.1\toolchain\opt\bin\arm-none-eabi-objdump.exe --syms -C -h -w c:\Soberlink\soberlink_sfw\trunk_NordicBLE\SL_Connect_ST\build_connect\zephyr\merged.hex
Reading symbols from c:/nordicsemi\v1.9.1\toolchain\opt\bin\arm-none-eabi-nm.exe --defined-only -S -l -C -p c:\Soberlink\soberlink_sfw\trunk_NordicBLE\SL_Connect_ST\build_connect\zephyr\merged.hex
Launching GDB: "c:\\nordicsemi\\v1.9.1\\toolchain\\opt\\bin\\arm-none-eabi-gdb.exe" -q --interpreter=mi2 "c:\\Soberlink\\soberlink_sfw\\trunk_NordicBLE\\SL_Connect_ST\\build_connect\\zephyr\\merged.hex"
Set "showDevDebugOutput": true in your "launch.json" to see verbose GDB transactions here. Helpful to debug issues or report problems
Run to 'main' timed out. Trying to pause program
I even tried to use a standard example (BLE peripheral) and got the same results. Any suggestions what could causing the bootloader to hang only while debugging?
Thanks and regards,
Pam
