I have been developing for several years with the nRF52832 and 52840 devkits. I have several of each available. One specific 52840 dk seems to have crashed code in the interface MCU. I found a thread several years old discussing how to re-flash the code, but the links there are all broken. Also, they all mention an IF reset/boot button, and i see no such item on my board. How should I go about re-flashing the IF MCU firmware?
It is indeed the Nordic devkit board, same one in your picture. I thought that reset button was just the nRF52840 reset. I used to laugh at folk who complained about the itty-bitty text I would squeeze into tight places like that - not so much any more, with my bifocals.
LED5 flickered briefly and then appeared to be on steady. Below is the journal from nRF Connect VS Code. After the first attempt I tried using west, but it's not in the system path so I used nrfjprog --recover instead, which appeared to work. Then I made two more attempts, performing the suggested corrections. Still no joy. What am I missing?
-- west flash: using runner nrfjprog
-- runners.nrfjprog: Flashing file: d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex
ERROR: The operation attempted is unavailable due to readback protection in
ERROR: your device. Please use --recover to unlock the device.
ERROR: runners.nrfjprog: Flashing failed because the target must be recovered.
To fix, run "west flash --recover" instead.
Note: this will recover and erase all flash memory prior to reflashing.
FATAL ERROR: command exited with status 16: nrfjprog --program 'd:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex' --sectoranduicrerase -f NRF52 --snr 1050267783
The terminal process terminated with exit code: 16.
Terminal will be reused by tasks, press any key to close it.
> Executing task: nRF Connect: Build: multi-NUS-master/build (active) <
Building multi-NUS-master
west build --build-dir d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build d:\304\FW\Hook\examples\ble_central\multi-NUS-master
ninja: no work to do.
Terminal will be reused by tasks, press any key to close it.
> Executing task: nRF Connect: Flash: multi-NUS-master/build (active) <
Flashing build to undefined
west flash -d d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build --skip-rebuild -r nrfjprog --dev-id 1050267783
-- west flash: using runner nrfjprog
-- runners.nrfjprog: Flashing file: d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex
Parsing image file.
ERROR: The file specified is not a valid hex file, has data outside valid areas
ERROR: or does not have data in valid areas.
FATAL ERROR: command exited with status 52: nrfjprog --program 'd:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex' --sectoranduicrerase -f NRF52 --snr 1050267783
The terminal process terminated with exit code: 52.
Terminal will be reused by tasks, press any key to close it.
> Executing task: nRF Connect: Flash: multi-NUS-master/build (active) <
Flashing build to undefined
west flash -d d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build --skip-rebuild -r nrfjprog --dev-id 1050267783 --recover
-- west flash: using runner nrfjprog
-- runners.nrfjprog: Recovering and erasing all flash memory.
Recovering device. This operation might take 30s.
Writing image to disable ap protect.
Erasing user code and UICR flash areas.
-- runners.nrfjprog: Flashing file: d:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex
Parsing image file.
ERROR: The file specified is not a valid hex file, has data outside valid areas
ERROR: or does not have data in valid areas.
FATAL ERROR: command exited with status 52: nrfjprog --program 'd:\304\FW\Hook\examples\ble_central\multi-NUS-master\build\zephyr\zephyr.hex' --sectoranduicrerase -f NRF52 --snr 1050267783
The terminal process terminated with exit code: 52.
Terminal will be reused by tasks, press any key to close it.
Hello,
Sorry for the late reply. I was out of office last week.
What version of nrfjprog do you have? Can you please try to update to the latest version? (I see that you have a DK with the new serial numbers (starting with 10...). Perhaps nrfjprog doesn't recognize that serial number.
I am using nRF Command Line Tools version 10.15.4, so try using that (I believe this is currently the latest version).
Can you please show me how you created the project that you are trying to flash? Either the initial build command or the project setup in VS Code. And are you trying to flash this using the nRF Connect for VS Code, or through the command line?
Also, is it possible to upload the .hex file that you are trying to flash here, so that I can have a look at what it is trying to flash. What area that it claims is outside the flash? It may be a bug where it doesn't recognize the UICR area, but that should succeed despite the programmer some times say that it is outside the flash. But I am not sure what area it refers to just by looking at the log.
BR,
Edvin
Hello,
Sorry for the late reply. I was out of office last week.
What version of nrfjprog do you have? Can you please try to update to the latest version? (I see that you have a DK with the new serial numbers (starting with 10...). Perhaps nrfjprog doesn't recognize that serial number.
I am using nRF Command Line Tools version 10.15.4, so try using that (I believe this is currently the latest version).
Can you please show me how you created the project that you are trying to flash? Either the initial build command or the project setup in VS Code. And are you trying to flash this using the nRF Connect for VS Code, or through the command line?
Also, is it possible to upload the .hex file that you are trying to flash here, so that I can have a look at what it is trying to flash. What area that it claims is outside the flash? It may be a bug where it doesn't recognize the UICR area, but that should succeed despite the programmer some times say that it is outside the flash. But I am not sure what area it refers to just by looking at the log.
BR,
Edvin
