Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I wanted to time stamp data which is sent via Bluetooth connection. Is there any pre defined functions to do that. Also please suggest any modifictions to be done...
Hi, I have a nRF52840 based Custom development board and a GSM module(AT command based) with UART and USB support. Because of lack of UARTs in nRF52840, I want to use USB...
Hi, I'm working on nRF9160 modem firmware update.
While working on nRF9160 modem, I found that it uses nrf_modem library which is precompiled library whose only API can...
Hello, I want to sampling voltage of 16 data sources, 8 of them are with amplifier, 8 of them directly connect to ADC pins, but I found that both nRF52810, nRF52832 and nRF52840...
I need to synchronise a time stamp on ant ANT slave with the master. Timesync would be ok but the message has to be acknowledged which ant timesync messages cannot do.
I...
Hi all,
I am trying to get my peripheral device to set an MTU size when connecting to the nRF Connect Android application that is not a value of 23. I have the following...
I've asked before about these two peripherals, the way they are presented is a little confusing.
I understand that UARTE has DMA possibilities, UART doesn't. Also that in...
I'm working on automating some of our builds for the nRF5340 in our CI, and
Currently, we can build these locally (on MacOS) with the NCS Connect VSCode toolchain, version...
Hi,
I'm experimenting the GPS on nrf9160 by using the ncs/samples/nrf9160/gps project. I set the GPS mode to be continuous mode. The 9160DK board is placed in a relative...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
What I want to do is to connect to Central, then bond and then disconnect.
Therefore, sd_ble_gap_disconnect...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
