Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
I wanted to time stamp data which is sent via Bluetooth connection. Is there any pre defined functions to do that. Also please suggest any modifictions to be done...
Hi, I have a nRF52840 based Custom development board and a GSM module(AT command based) with UART and USB support. Because of lack of UARTs in nRF52840, I want to use USB...
Hi, I'm working on nRF9160 modem firmware update.
While working on nRF9160 modem, I found that it uses nrf_modem library which is precompiled library whose only API can...
Hello, I want to sampling voltage of 16 data sources, 8 of them are with amplifier, 8 of them directly connect to ADC pins, but I found that both nRF52810, nRF52832 and nRF52840...
I need to synchronise a time stamp on ant ANT slave with the master. Timesync would be ok but the message has to be acknowledged which ant timesync messages cannot do.
I...
Hi all,
I am trying to get my peripheral device to set an MTU size when connecting to the nRF Connect Android application that is not a value of 23. I have the following...
I've asked before about these two peripherals, the way they are presented is a little confusing.
I understand that UARTE has DMA possibilities, UART doesn't. Also that in...
I'm working on automating some of our builds for the nRF5340 in our CI, and
Currently, we can build these locally (on MacOS) with the NCS Connect VSCode toolchain, version...
Hi,
I'm experimenting the GPS on nrf9160 by using the ncs/samples/nrf9160/gps project. I set the GPS mode to be continuous mode. The 9160DK board is placed in a relative...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
What I want to do is to connect to Central, then bond and then disconnect.
Therefore, sd_ble_gap_disconnect...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
