I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I'm getting a strange amount of error when trying to measure the battery for a custom PCB based on the nrf9160.
Details
My VCC_IO is 1.8V
My max battery voltage is...
Hi,
Perhaps I have a misunderstanding of this GNSS Socket Option.
In the GPS Sample Project (samples/nrf9160/gps) with a nrf9160-dk and no connected GPS Antenna, I set...
Hello, I am trying to add a watchdog timer to my code which consists of THREE threads, so I referred to the task_wdt example in Zephyr/Samples/Subsys for SDK1.6.1.
Based...
Hi,
I wonder if there is a smart and easy way to implement a fallback if I use the MQTT connection with a static IP. What I want is if the IP fails to connect it tries again...
this error shows after the 100% completion of memory flash as shown in the screenshot below. after showing the error , nrf52840 pulsing led turns off automatically.
Note...
Greetings All,
I am trying to connect an nrf52840dk board to an nrf52840dongle for wireless serial communication.
I flashed the nrf52840dk with the central_uart sample...
Hello,
I am using nrf52832 and i am using a SW similar to the beacon.
I tried 2 configuration:
tx_power = 0 (0 dbm)
tx_power = 4 (4 dbm)
I tried to measure the...
Hello,
I'm familiar with the GPIO and GPIOTE peripherals,
The GPIOTE has 8 channels, so it can use 8 GPIO pins to fire interrupts.
Some questions:
- Can the 8 Channels...
Hi ,
I have compiled in Heart rat relay into my app; can scan and connect to simulator and garmin HR straps; but fail to connect to polar. My debug log shows...
...
I've successfully built the 'direction_finding_connectionless_tx' project and flashed that to an nRF52833dk, and built the 'direction_finding_connectionless_rx' project with...
Hi,
I'm using a NRF52811 on a custom board and I would like to change a project from a NRF52832 with S132 to it.
I only use supported functions from the S113, but I...
how to set the High-drive QSPI?
NRF_GPIO_PIN_H0H1
nrf_gpio_cfg ( mosi_pin ,
NRF_GPIO_PIN_DIR_OUTPUT ,
NRF_GPIO_PIN_INPUT_CONNECT ,
NRF_GPIO_PIN_NOPULL ,
NRF_GPIO_PIN_H0H1...
Environment:
- OS: Ubuntu 20.04 (Docker container)
- NRF SDK: v1.4.0
- Zephyr: v2.4.0-ncs1
I am trying to build my project for native_posix. I am getting some build...
