Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
Hi Nordic,
I am working with nRF52840, sdk17.1.0 and do the following test:
I use nrf_gpio_cfg_output(), nrf_gpio_pin_set(); to set gpio P1.00 to high and use nrf_gpio_pin_input_get...
Hi Nordic:
Test with board nrf5340-dk ncs v1.9.1
prj.conf
# Console
CONFIG_LOG = y
CONFIG_LOG_PRINTK = y
CONFIG_LOG_DEFAULT_LEVEL = 3
# UartConsole
CONFIG_UART_CONSOLE...
Good morning:
I'm trying to develop the twi_scanner with the nrfx libraries. Everything seems to compile fine, but at the end of the Build process I get:
d:/ncs/v1.9...
Currently I am trying to adapt the Radio Test example to function on our custom hardware which uses the nRF52840 SoC. We need the Radio Test firmware to give access to the...
Hi All,
I have a nRF52840 DK board. Which I bought about 1.5 years ago. I used to do some development using Segger Embedded Studio those days.
Now I have setup the Zephyr...
Right now there are 2 supported codecs: SBC and LC3. It also looks like that they are implemented in software.
Can we have other audio codecs (i.e. LC3plus HR, aptX or LDAC...
Hi Nordic Support,
I have been waiting for many years to see our end-user devices (Android, iOS, Windows, and Linux) such as smartphones, tablets, and computers to support...
Hi, I hope you had a nice weekend.
In my project, I basically need to output some data over GPIO from a memory buffer (highs and lows). Currently I'm doing this with a timer...
Hi All!
I am using ble_app_multilink_central and ble_app_blinky examples for concurrent connections of 4 devices ( (1)nrf52833 as central and other (4) as peripherals(nrf52833...
I'm using modules from minew, those are MS50SFB2 based on nRF52810 and developing in nRF5_SDK_17.1.0_ddde560 and segger studio 6.30 on windows 10.
I was trying some examples...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
Hello:
My project needs A-GPS function, so I made an application about " SUPL client library license signup"
but it was rejected:
Dear Harry,
your application...
I've been building a test application, and it's gotten bigger and bigger over time. Everything compiles perfectly. I'm building the ns version for the app core. nrf5340dk_nrf5340_cpuappns...
