here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
The RPM package for Linux x86 64 bit has its architecture set to amd64, but the correct value should be x86_64. This problem prevents installing the RPM on current versions...
I have a question about BD_ADDR.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) device: EYSHJNZWZ (nRF52832)
1) Is it possible to change...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
Dear customer support,
the datasheet of the NRF52810 states that its operating temperature is: -40...+85°C
Could you please clarify the following points?
- How is...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello !
I'm currently discovering the VS code extension for nRF Connect SDK and I whish to give some feedbacks of missing / odd features. I hope this is the best place...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
Hi,
Since NCS 2.0 dosent support SES anymore, I've started using nrf connect in vscode recently.
Here are some problems I met:
1. It takes almost 5 mins to loading everytime...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
Hi
we got three nrf5340 audio dk, because we are still waiting for LC3 code authorization， so, I wonder how to config the sample project nrf5340_audio to use the open-source...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
