Hello,
I am a firmware engineer in taiwan.
I already use nRF52820 to finish a case. This case have DFU function. The DFU function can work ,but when I use (nRF Connect...
Hi,
Due to shortage of pins SPI CS is reconfigured as GPIO while SPI is not used. Soft device is not used.
Problem is the delay that is needed after nrfx_spis_uninit call...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
1) Our device uses NRF52832 to connect with Android 7 system，use wireshark to monitoring，find not hop，is OK？ and wireshark delta time is Connection Interval ?
2) nrf52832...
I have controlled an LED with a push button connected to GPIO pins P0.03, P0.04 respectively.Now I want to use those pins as CLK and DIO pins of TM1637 Display.I wrote a basic...
Hello,
I am now developing firmware for nRF52840 DK and nRF52840 dongle. My target is to develop a firmware that my DK/dongle be central and can send command to peripheral...
In SES, it is possible to clean when project is opened , Rebuild ALL, clean solution, clean zephyr and as well from Project -> Reload project, it is possible to update. How...
Hi All,
We have been using NRF52 products for a few years now and currently doing an PoC of using the BLE DFU with a CODED_PHY.
Our solution does use the DFU already but...
I am using the nrf_serial library SDK 15.2.0. I have implemented the solution suggested in Case ID: 216973 for recovering from driver errors. This helped me get over errors...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
Hi,
When battery short circuit, nPM1100 need VBUS 5.3V to activate?
Why does VBUS need 5.3V connection to work?
Thank you for all your assistance. Kind regards, Peter...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
Hello Team Nordic,
Greetings of the day!!
We are currently testing the current of our device with the PPK2 kit.
We use the ESP32 as MCU and we are switching Cellular...
Hi,
I recently added the DEBUG_NRF preprocessor definition to my project because I wanted to use the nrf_assert module in some of my files. Now my project is crashing a...
In the nRF52840, I used the app_usbd_cdc_acm_write(&m_app_cdc_acm,tx_buf,size) method to output the data.
At the beginning, I use the pyserial to read the output data...
Hi,
I'm developing a software in python 3.9.6 64-bit which program a nRF9160 and nRF52840 using pynrfjprog.
The software is working from vscode debug session. But when...
Hi,
We are doing an analysis of power usage using a roaming sim vs home sim since the roaming sim data charges tend to be cheaper. (You wouldn't have happened to have done...
I use flash and erase button at Visual Studio Code but get warnings: I use custom board, nrf sdk 1.9.1
1. How to deal with warnings?
2. After erase and flash the device...
hi,
i m working to create a zigbee network using demo example of light bulb given in sample project of nrf5340dk.
as of now i am able to connect 2-3 bulb devices(i.e....
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
Hi there,
I am trying out the nRF Connect SDK v1.9.1 with a custom board (with an nRF52833) that we have produced. I have set up the necessary plugins in VSCode (v1.67.2...
