I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I'm trying to wrap my head around the APP_USBD driver, but I'm running into a mental block. I am implementing a report descriptor for the Battery System usage page, and all...
Hello, I have been using the SPM to read the UICR->OTP[0] register in SDK1.2.1, 1.4.2, and 1.5.1 but it's not able to when I'm using version 1.9.1.
I have patched the \1...
Hello together,
Im currently doing my bachelor thesis and my task is to develop a user interface that can control a NRF52840 and write some parameters over UART.
Im...
Hello dear nordic team, how can I get all sensor data with the same time stamp in a uniform frequency? The 'Asset Tracker' application is on the Thingy:91. Best regards, ...
Hello,
I am successfully able to open and close adapter for nRF52840 using pc-ble-driver-py using python3.6.0 on my host armv7 Linux board.
But doing same inside the docker...
I got MCUBoot running using signed images. Now I want to enable encrypted images using the build tools, but how? I've found this pull request: https://github.com/zephyrproject...
Hi,
We are developing BLE firmware that will allow BLE pairing without bonding (but with PIN/Passkey that is entered from the phone). However, when I try this with nRFconnect...
Hello Nordic Support.
I would like to build and use a Sniffer using a PC (Windows 10), nRF52DK, and nRFConnect for desktop.
Please teach me about the following.
nRFSniffer...
Hi, I can successfully build the Matter light bulb example in nRF Connect SDK 1.9.1 but I fail to do the same in v1.9.99-dev1.
What did you change?
Here the error:
west...
Dear DevZone support team
I'm facing the following problem: My application uses the Zephyr's BLE stack and basically does not much beside parsing JSON-messages received...
Hi,
I tried to implement PPI for a very timing sensitive application. The sample PPI_trace uses the RTC but it is too slow for my application so I'd want ot use timer0...
Hi,
I am following these steps to build a sample project to try out OTA updates of the firmware. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software...
Hello,
We would like to use BLE to transmit a lossy data stream at high data rate. Looks like Isochronous channel is the best choice. How's the Isochronous channel is...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
