I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Dears, I used NRF9160 and i have some questions about it: 1. the internal rtc is accurate or not ? is calibrated or need to be calibrated every time? 2. this rtc is internal...
Hi,
I use FDS to save my data in my application. Below is my fds list. All RECORD already have data from factory production.
#define FILE_ID 0x1111 #define RECORD_KEY_TORQUE_0...
Dear Members,
How can I scan continously if I loss the sensor,
I have made at this function :
static void ant_evt_handler(ant_evt_t * p_ant_evt, void * p_context)
...
Dear Members,
I got :
Could not find core in Coresight setup nRF52840 ? with PCA10059, it was working ok before,
Any solution for it ?
Kind regards,
Rixtronix...
Hello,
i've nRF5340-DK, 3 wire SPI oled model.
any one can change STM32F103 code for NCS1.9?
the oled can light on, but no show text, maybe SPI recv Font incorrect....
Am I the only one who finds Zephyrs I2C implementation a little cludgy? Or am I just missing something?
It may be that I'm just used to bare metal I2C but I can't seem to...
I'm working on a Central/Peripheral device and will need to set both:
CENTRAL_LINK_COUNT 1
PERIPHERAL_LINK_COUNT 1
It mentioned that if either of these values are changed...
Hi,
I'm trying the "Heart Rate Application" example on nRF52 DK. I successfully compiled and downloaded the hrs_example code to the board. When I used Toolbox app on the...
The Cortex-M4 exception handling and NVIC support late-arriving exceptions as discussed for example in the Cortex-M4 Generic User Guide. In this regard, my question is: What...
Hello,
I have been trying to get the UART working with EasyDMA on the NRF52832 development kit. I did have some success yesterday, but it's not working again today for some...
Hi,
I am working on a prototype which I have almost completed, I am using this NRF52832 chip, using BLE and creating a mesh network, where different nodes are communicating...
Hello,
I would like to know if Matter template example is compatible with nRF52840 Dongle. According to Matter Template example website ( developer.nordicsemi.com/.../README...
Hi,
I am using nrf5340 with Zephyr and nrf connect sdk 1.7.0 to drive two SPI bus devices off the same bus.
I have no problem configuring the SPI bus using nrfx_spim as...
