Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi there,
We are trying to integrate an nRF21540EK shield onto our nRF5340DK. Following the instructions on the following link ( https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello
My production ble performance is lower then nrf52DK.
How can I impove ble performance?
And I think there are two ways.
1. redesign PCB antenna (currently...
So, I'm trying to debug some code I've been working on, so set CONFIG_LOG=y in my prof.config file.
Now, when I try and builld, I get this error:
Error: Image size (0x36c54...
Hello everyone,
I am using the nrf52840 on the CDEBYTE E73-2G4M08S1C nRF52840 BLE 5.0 Wireless Transceiver. robiz.net/e73-2g4m08s1c
There are two device. One of them central...
nRF52840, SDK version 17.0.2_d674dde, SD140.
Our code uses the PPI extensively to manipulate some GPIOs and start SPIM transfers from peripherals using EasyDMA to store...
Hello all! I am trying to interface MPU6050 with nrf52832 dk using the following code. On the LOGGER, I see that the MPU isn't detected, despite I replaced the MPU. The if...
I wrote a reply to a 5-year old question which appeared to be related to my needs but the answer was not what I was looking for.
The case is very straight forward:
The...
Good morning Sir/Mam
i want to read data on serial using nrf9160 by segger. i have pic a sample from devzone "Uart". i have successfully build it and Run on board , but...
Hi,
I am having problem with UART on both NRF52 Devkit nad NRF52480 dongle. If I start from the example:
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart...
Hi,
at Bluetooth core specification v. 4.2, vol. 3, part G, chapter 4.9.3.
An Error Response shall be sent by the server in response to the Write
Request if insufficient...
I use the nrf examples direction_finding_connectionless_rx,firstly i have no attena array,the other as describled i do by steps.
I use two nrf5340 boards.with building,i...
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
