Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
I am enabling bonding, but the nRF Connect application and it does not show the peripheral ( nRF52833 ) device is being bonded. Is there any other thing I am missing ?
SDK...
Hi,
Still have no answer for this problem, so I repeat again.
I have got the reply that the bootloader do not impact the application, so please check these videos.
VIDEO...
Hi guys,
When testing the MQTT connection on ncs 1.9.1, modem V1.3.1, when calling lte_lc_nw_reg_status_get to query the LTE signal status, the debugging found that there...
i have built and run "light switch " example given in nrf5340 sdk, i m using nrf5340dk to upload this example code, searched online , but unfortunately not getting any clue...
Hello,
In my project i am using stepper motor with nrf52840 and here i want to run my stepper motor for particular amount of time like i want to expel a particular amount...
I need a HCI controller only build for nRF52840, test on zephyr.
1) Build and flash for controller.
cd ~ /zephyrproject/zephyr/samples/bluetooth/hci_uart
mkdir build...
Hi,
The product we are developing needs to support extern Flash-based FOTA, so I downloaded the ble_extFlash sample from the following link for reference:
https://github...
PCA10121 schematic diagram U1 nRF5340 MCU is responsible for LE Audio, U11 nRF5340 interface MCU is responsible for programmer/debugger. Can you provide related software development...
I try to DFU on RaspberryPi OS by usb-serial. I put nRF52840 dongle on USB port of RPI4. And press reset button of the dongle.
I got error on nrftuil.
$ nrfutil dfu...
Hi there,
Yet again we are running into very basic issues with the nordic tools and software, and this is adding up to cost us massive amounts of time.
Within nrf connect...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
