Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
Hi there,
We are trying to integrate an nRF21540EK shield onto our nRF5340DK. Following the instructions on the following link ( https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello
My production ble performance is lower then nrf52DK.
How can I impove ble performance?
And I think there are two ways.
1. redesign PCB antenna (currently...
So, I'm trying to debug some code I've been working on, so set CONFIG_LOG=y in my prof.config file.
Now, when I try and builld, I get this error:
Error: Image size (0x36c54...
Hello everyone,
I am using the nrf52840 on the CDEBYTE E73-2G4M08S1C nRF52840 BLE 5.0 Wireless Transceiver. robiz.net/e73-2g4m08s1c
There are two device. One of them central...
nRF52840, SDK version 17.0.2_d674dde, SD140.
Our code uses the PPI extensively to manipulate some GPIOs and start SPIM transfers from peripherals using EasyDMA to store...
Hello all! I am trying to interface MPU6050 with nrf52832 dk using the following code. On the LOGGER, I see that the MPU isn't detected, despite I replaced the MPU. The if...
I wrote a reply to a 5-year old question which appeared to be related to my needs but the answer was not what I was looking for.
The case is very straight forward:
The...
Good morning Sir/Mam
i want to read data on serial using nrf9160 by segger. i have pic a sample from devzone "Uart". i have successfully build it and Run on board , but...
Hi,
I am having problem with UART on both NRF52 Devkit nad NRF52480 dongle. If I start from the example:
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart...
Hi,
at Bluetooth core specification v. 4.2, vol. 3, part G, chapter 4.9.3.
An Error Response shall be sent by the server in response to the Write
Request if insufficient...
I use the nrf examples direction_finding_connectionless_rx,firstly i have no attena array,the other as describled i do by steps.
I use two nrf5340 boards.with building,i...
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
