Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi guys,
So lately, I decided to update the sdk from 4.1.0 to 4.2.0 and there are some problem that I can not solve myself. So I use the macro ZB_ZCL_REGISTER_DEVICE_CB...
Dear Nordic,
We are developing nRF21540 + nRF5340 solution.
As there seems to be many versions of matching components depending on which source of information is used...
The RPM package for Linux x86 64 bit has its architecture set to amd64, but the correct value should be x86_64. This problem prevents installing the RPM on current versions...
I have a question about BD_ADDR.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) device: EYSHJNZWZ (nRF52832)
1) Is it possible to change...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
Dear customer support,
the datasheet of the NRF52810 states that its operating temperature is: -40...+85°C
Could you please clarify the following points?
- How is...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello !
I'm currently discovering the VS code extension for nRF Connect SDK and I whish to give some feedbacks of missing / odd features. I hope this is the best place...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
Hi,
Since NCS 2.0 dosent support SES anymore, I've started using nrf connect in vscode recently.
Here are some problems I met:
1. It takes almost 5 mins to loading everytime...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
