We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
I am trying to download SUPL client library but got an email that my request was denied. I've used the same email address as the one here. Can you please advise?
Kind...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i need help.
We use nrf52840 and DK17.0.2
Using saadc with oversampling x8 , Single-ended mode.
Question
When Event monitoring using limits , Is the timing at which...
I'm using three low power PWM instances driving three separate IO pins open an nRF 52810 and need to be able to re-configure each of the channels on the fly to select opposite...
https://devzone.nordicsemi.com/f/nordic-q-a/69596/device-initialization-problems/285611#285611
had gone through above thread.
I am struck exactly at this point.
i...
Hi
I am using 52832 peripheral role.
sdk16.0
ble_uart add one character 0xff03 which have notify attribute
have these function
1. Use connectable broadcast on no...
Dear Nordic Engineers
I study central code,I find a param ble_gap_evt_adv_report_t
I can understand other param of ble_gap_evt_adv_report_t,but I don't understand set_id...
The NFC pins of my nRF52840 MCU have been set to be used as GPIO pins through the NFCPINS register. I can toggle the GPIO lines just but I find that after power on that the...
Hello,
been trying to add lte_lc_connect_async(lte_handler) to mqtt_simple, just like the way it is in sample aws_iot. Instead getting a failed response.
Now not sure...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
If while using the nRF Connect for Desktop you are seeing this message on the log
Make sure to installe the Universal JLink Segger from www.segger.com/.../
I'm using a sample from nRF connect SDK v1.91.1 for BLE peripheral. I'm trying to read one of the buttons on the development kit, but I'm not very sure how to use the button...
Have been trying to run nRF9160 LwM2M client sample. A problem is that it doesn't appear to be initialising the modem properly, by trying to access the network when the modem...
