We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
We are working toward certification of our product and conducting TRP/TIS measurements. The TRP and TIS are not matching up with the conducted output power and...
I'm having a hard time developing for Nordic Hardware right now as it seems that the hardware is not recognized by VSCode/NrfConnect anymore. Under the Connected Devices Section...
Dear,
I use an nrf5340 dk with sdk 1.8.0 for vscode. I'm now playing with the central_and_peripheral_hr example and I want to change the advertisement packet. How and where...
Hi,
I have an issue in regard to Matter. I would like to commision a device in my network, but I don't know why the Python CHIP Controller returns this error every time...
Hello supporters and enthusiasts,
I'm developing a BLE product which mainly works as central role for all scenarios.
The steps how the central controls to a peripheral...
With the release of NCS v2.0.0, is v1.9.x EOL? If not EOL, how long will it be supported, will there be a 1.9.2 or beyond?
Trying to decide if we should look at migrating...
Last year i asked about a custom nRF5340 board when using NCS V1.7.0 and the comment was to just copy the entire nRF5340DK into my custom board folder and modify the names...
Hello,
We have a pre-production design of a custom board that has an nRF5340 on it. We have built and programmed about 60 boards of this design without any issues using...
dear all，
I want to know how to estimate ram of softdevice use.
For example, as a central, how much ram will be required when adding a custom ble service,
and how much...
Hello
I added the mesh shell module to my app running on nRF52480 custom board and I am trying to provision and enable publication on the custom model I have
This produces...
Hii. I was using scheuler and wanted to know how this part of code works. The #define CRITICAL_REGION_ENTER() has opening bracket but it is closing after #define CRITICAL_REGION_EXIT...
Hi，
I use nRF9160 SPI to drive Epson's screen， The screen MAX writing apeed is 6M，But reading apeed is only 1M，So I need to switch SPI speed between read and write。
I...
I'm more or less copying the thingy:91-design. The Qourvo 12038 used in the design is EOL, and at the moment not available. It seems the alternatives use MIPI-interface. Can...
Hi,
I´ve been trying to improve data transmission from an nRF91 dev board through nb-iot to Azure IOT-hub and always got a socket disconnection event when I tried to send...
