Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello
I'm using an nrf52840 (PCA10059) together with an nrf24l01 (ESP32, MIRF Library).
My goal is to send a data packet from the nrf52840 which the nrf24l01 can receive...
Hi there,
the nRF58240 SoC supports a wide range of hardware-accelerated cryptography features using ARM's CryptoCell310. However, I'm unable to use many of the features...
I dwnload the nrf connect for desktop in my pc.i want to use the VS extension foe NRF.But i have had NCS 1.9.0 and 1.9.1 .The SDK of NCS is from my baidu pan.so i only install...
Hi! We are trying to make our project more secure following the Nordic documentation, but we absolutely don't know how to change the values of our registers, furthermore is...
I use the development version of NRF5340 DK, using the routine is ISO_broadcast, but the following error occurs, may I ask whether the controller does not support it?
...
Hi,
I just want to learn if we can use high-freq clock to measure time in nanosecs precision.
SoC: nRF52840
SDK: nRF Connect SDK (v1.9)
I know that it was not possible...
Hi guys,
I am experimenting with OTA buttonless DFU.
I included the Buttonless Secure DFU Service to my application and I managed to flash the new image over the air through...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
Hi Friends!
I want to do this on the nrf52840:
time start
do some code
time stop
print stop-start and get time
Im using nrf connect extension for VScode
Does...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
