Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I have a question about BD_ADDR.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) device: EYSHJNZWZ (nRF52832)
1) Is it possible to change...
Hi,
IC nRF52833
sdk:nRF5_SDK_17.1.0
1. Does BLE have the concept of signaling test mode and non-signaling test mode?
2. Is DTM in signaling mode or non-signaling mode...
Dear customer support,
the datasheet of the NRF52810 states that its operating temperature is: -40...+85°C
Could you please clarify the following points?
- How is...
If we are using the 5340 in high voltage mode (VDDH); what IO voltages are used for the debugger interface? Looks like our HW designer has taken the lip voltage 4v3 to 3v5...
Hello !
I'm currently discovering the VS code extension for nRF Connect SDK and I whish to give some feedbacks of missing / odd features. I hope this is the best place...
Hello,
We are using Nordic sdk 17.1.0, with segger studio of 5.70a.
Here we are trying to merge ble_app_uart example with ble_app_beacon example.
Actually ble_app_uart...
Hello,
I've been playing around with the PPK2. However, when I power a 1KR resistor with 3V I get an incorrect measurement.
The Expected current is 3/1000=3mA, I also...
Hi,
Since NCS 2.0 dosent support SES anymore, I've started using nrf connect in vscode recently.
Here are some problems I met:
1. It takes almost 5 mins to loading everytime...
When I build the smp_svr example, which I think contains firmware update over BLE functionality, the flash memory is reported as about 72% full.
Does this mean when I...
Hi, I use AT command controls the GNSS use Serial LTE modem example in my 91DK board.
I send command as below example,
but my uart tool receive as blow, and i don't...
What is the difference between nRF 5 SDK (downloaded in .zip format) and nRF Connect SDK v1.9.1 ?
I am using VSCode through nRF Connect SDK v1.9.1 and I find it easy to...
Hi
we got three nrf5340 audio dk, because we are still waiting for LC3 code authorization， so, I wonder how to config the sample project nrf5340_audio to use the open-source...
I am connecting a nrf52480 board (Adafruit Feather nRF52840 Express) as Connectivity chip and a custom board as Application chip for Nordic serialisation. Able to establish...
I am connecting a nrf 52480 board(Adafruit fether express) to a custom M4 cortex board with the help of nordic serialisation library. I have ported the serialisation library...
Hello all!
I'm using nRF52-DK to develop program which is controlled by smartphone (BLE) and do ADC&GPIO in the circuit.
GPIO acts like this: High-Low-High-Low.... it...
