It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi, I am trying to follow the nRF Connect Fundamentals course and have just built the Blinky app. It actually builds fine, but on the console it does show that there is 1...
The nrf52 is waking from a sd_power_system_off() and resets. The reset reason register indicates it was from a DETECT from GPIO, yet the LATCH register is 0 and all the sense...
Hello,
I'm writing my own UARTE library because I need some functionality not offered in the SDK. But I came across a hardware behaviour I can't explain.
In my understanding...
Hello,
Right now our application developed using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip.
Need help on migrating to BLE 5.
Which SDK & soft device...
My peripheral_demo is already able to work. Now I'm trying to add dfu to it.
I followed the instructions here. (+) Add DFU support to your application - Software - nRF Connect...
Hi,
Our customer is optimize the size of flash used of nRF5340.
They are curious whether the definition in autoconfig.h are all used in the image? or some of them are...
Hello,
I am working on BLE+Thread multiprotocol and took ble_thread_swi_template as a base code. I am using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8. My development...
Hello,
We're working with nRF52833 & nRF52840 and I'm trying to figure out why we've ~0.3ms IRQ Latency from the moment I call the function " uart_irq_tx_enable (dev );...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising. Since there is no example of "pure" extended advertising...
Hi,
I work on a project that required a sector in flash to store some information hence I changed the partition in the pm_static.yml file and the dts file (although I guess...
Hi,
I am writing an application that reads data from the I2S interface, adds it to a queue and sends it via BLE (the code I have implemented so far is added at the end of...
Is there any available binary firmware for nRF5340 Audio DK to evaluate and demo the LE audio case?
I tried to use the nRF5340 Audio DK for LE audio, but found the LC3 codec...
Hi,
We are trying to move from segger studio build environment to GCC/Make starting from the Example Makefile and adding source files and includes. The project consists...
Hi,
I am currently working on a project using a nrf9160 board (sdk 1.7.1 and Modem FW 1.3.1) and I am using PSM.
During my test, I put the board in a metal box to simulate...
