Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi
I have a question about reset Bluetooth, how can I do that?
I don't want to reset the system only to reset ble, turn on and turn off the ble,
thanks and regards
Hi guys,
This is my first BLE project. I want to send sensor data from my nrf52840 dk to my dongle. I know how to make an advertise but I can’t find a way to send my sensor...
Hi!
We'd like to understand the most reliable way for DFU OTA our Nrf52840DK boards over a "serial" topology network?
We are using nRF5 SDK 15.2.0 and our configuration...
we have nRF52832 controller
now we would like to choose the softdevice S132 or S112
how can i select the softdevice?
where can i find the difference between S!32 and...
Hello, Technical support team
In the past, I contacted you to confirm nRF52832 application.
This time, I have a question for a external reset as follows.
My application...
Hey there,
We are working with NRF52832 WLSCP package,
We had stated certification process , for BQB testing need to use the Radio test example with UART between EUT...
Hi,
We are using Nordic BLE-NRF52833 Module one of our products. We are developing our own windows application(using C# language) to communicate the information to our Product...
Hi! Reading this ticket, and the nRF Connect SDK and nRF5 SDK statement , I understand that the PC-BLE-Driver, whether the Python or JS variant, are in maintenance mode, and...
Is there some example for Encode / Decode with AES algorithm in ECB and CBC modes using Segger studio?
For a start, I only need the ECB mode that should be implemented in...
I have checked the qDEC example, I don't know what it is doing, so I can directly say what I need. I connected a Hall sensor to two pins of 52840, and configured QDEC. I set...
Hi, I am just doing some testing using Nordic Thingy:91 and already available firmware and cloud. I am in the very initial stage of learning about it and preparing it for...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hi All,
I'm using nrf Connect SDK v1.7.0 with Vs Code
So here I can see in the debug prints that Bluetooth device is able to get connection successfull callback and Immediately...
