Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Here is my situation:when I run the project "i2c_mpu9250",it worked. But when I applied it to "Ble_app_uart",in which I wanted to trans datas from nRF to Iphone, it failed...
Hello
I'm using an nrf52840 (PCA10059) together with an nrf24l01 (ESP32, MIRF Library).
My goal is to send a data packet from the nrf52840 which the nrf24l01 can receive...
Hi there,
the nRF58240 SoC supports a wide range of hardware-accelerated cryptography features using ARM's CryptoCell310. However, I'm unable to use many of the features...
I dwnload the nrf connect for desktop in my pc.i want to use the VS extension foe NRF.But i have had NCS 1.9.0 and 1.9.1 .The SDK of NCS is from my baidu pan.so i only install...
Hi! We are trying to make our project more secure following the Nordic documentation, but we absolutely don't know how to change the values of our registers, furthermore is...
I use the development version of NRF5340 DK, using the routine is ISO_broadcast, but the following error occurs, may I ask whether the controller does not support it?
...
Hi,
I just want to learn if we can use high-freq clock to measure time in nanosecs precision.
SoC: nRF52840
SDK: nRF Connect SDK (v1.9)
I know that it was not possible...
Hi guys,
I am experimenting with OTA buttonless DFU.
I included the Buttonless Secure DFU Service to my application and I managed to flash the new image over the air through...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
Hi Friends!
I want to do this on the nrf52840:
time start
do some code
time stop
print stop-start and get time
Im using nrf connect extension for VScode
Does...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
