Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi there,
We are trying to integrate an nRF21540EK shield onto our nRF5340DK. Following the instructions on the following link ( https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello
My production ble performance is lower then nrf52DK.
How can I impove ble performance?
And I think there are two ways.
1. redesign PCB antenna (currently...
So, I'm trying to debug some code I've been working on, so set CONFIG_LOG=y in my prof.config file.
Now, when I try and builld, I get this error:
Error: Image size (0x36c54...
Hello everyone,
I am using the nrf52840 on the CDEBYTE E73-2G4M08S1C nRF52840 BLE 5.0 Wireless Transceiver. robiz.net/e73-2g4m08s1c
There are two device. One of them central...
nRF52840, SDK version 17.0.2_d674dde, SD140.
Our code uses the PPI extensively to manipulate some GPIOs and start SPIM transfers from peripherals using EasyDMA to store...
Hello all! I am trying to interface MPU6050 with nrf52832 dk using the following code. On the LOGGER, I see that the MPU isn't detected, despite I replaced the MPU. The if...
I wrote a reply to a 5-year old question which appeared to be related to my needs but the answer was not what I was looking for.
The case is very straight forward:
The...
Good morning Sir/Mam
i want to read data on serial using nrf9160 by segger. i have pic a sample from devzone "Uart". i have successfully build it and Run on board , but...
Hi,
I am having problem with UART on both NRF52 Devkit nad NRF52480 dongle. If I start from the example:
nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_uart...
Hi,
at Bluetooth core specification v. 4.2, vol. 3, part G, chapter 4.9.3.
An Error Response shall be sent by the server in response to the Write
Request if insufficient...
I use the nrf examples direction_finding_connectionless_rx,firstly i have no attena array,the other as describled i do by steps.
I use two nrf5340 boards.with building,i...
When I connected the usb and turn the DK switch on, the DK didn't turn on. After leaving for a few minutes, the DK started to turn on and off then eventually stables and fully...
Hi,
I am working on nRF5 Thread 4.1.0 and I am trying to do implement Thread secure DFU.
I am following infocenter.nordicsemi.com/index.jsp
i have run the command...
We are working on a project in which we have integrated multiple modules and examples like GPS, IMU Sensor, SD card, Bluetooth, etc. Now I have to manually shut down all the...
