I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I have an "Aqara Wireless Mini Switch" ( https://www.amazon.com/gp/product/B07D19YXND ) which identifies as a Xiaomi WXKG11LM. This button is designed to send semi-nonstandard...
I'm trying to receive an HTTP response of approximately 100KB using the nrf9160 modem. When the response size is small recv works fine. When response is large recv returns...
GReetings,
Having a hard time using nRF Connect v3.11.1 for Desktop freshly installed on a Windows based laptop (Windows 10 Family 21H2)
J-Link V7.58b was installed simultaneously...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I have a nRF9160DK and am trying to install the nRF Connect SDK and have run into troubles. First, I am unable to launch VS Code from the Toolchain Manager. I have seen...
Good morning!
I am testing an application on Visual Studio Code + nRF Connect. I have a crash:
<err> os: Faulting instruction address (r15/pc): 0x0002c064
How can...
I have code that looks something like this:
static void some_worker(struct k_work *work) { struct state *state = CONTAINER_OF(work, struct state, some_work); k_spinlock_key_t...
My DK is connected via USB to my PC.
Uptill tommorrow it was connected and today it is saying not connected.
How to fix this ? Not sure what happened.
See below:
Have been trying to run nRF9160 sample code, including LwM2M client, and at client (latest nRF9160 firmware 1.3.2, latest SDK and Link Monitor 2.0.1) but in LTE Link Monitor...
I am unable to properly erase UICR registers on network core.
flash_erase() function that I call before flash_write() doesn't take any effect.
Example: 1. Set UICR->CUSTOMER...
I have not been able to create a stable development environment in macOS Monterey using the automatic installation process.
In order to better understand and document the...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
In general, what are the steps to adding a device using GPIO pins.
My thoughts are to physically connect my peripheral to the board and configure the device tree using an...
Hello Nordic Team,
I have a nRF52833 DK with me.
I am using nRF Connect SDK v1.8.0 and through that using Segger Embedded studio loaded the Light switch example to nRF52833...
