I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hello supporters and enthusiasts,
I'm developing a BLE product which mainly works as central role for all scenarios.
The steps how the central controls to a peripheral...
With the release of NCS v2.0.0, is v1.9.x EOL? If not EOL, how long will it be supported, will there be a 1.9.2 or beyond?
Trying to decide if we should look at migrating...
Last year i asked about a custom nRF5340 board when using NCS V1.7.0 and the comment was to just copy the entire nRF5340DK into my custom board folder and modify the names...
Hello,
We have a pre-production design of a custom board that has an nRF5340 on it. We have built and programmed about 60 boards of this design without any issues using...
dear all，
I want to know how to estimate ram of softdevice use.
For example, as a central, how much ram will be required when adding a custom ble service,
and how much...
Hello
I added the mesh shell module to my app running on nRF52480 custom board and I am trying to provision and enable publication on the custom model I have
This produces...
Hii. I was using scheuler and wanted to know how this part of code works. The #define CRITICAL_REGION_ENTER() has opening bracket but it is closing after #define CRITICAL_REGION_EXIT...
Hi，
I use nRF9160 SPI to drive Epson's screen， The screen MAX writing apeed is 6M，But reading apeed is only 1M，So I need to switch SPI speed between read and write。
I...
I'm more or less copying the thingy:91-design. The Qourvo 12038 used in the design is EOL, and at the moment not available. It seems the alternatives use MIPI-interface. Can...
Hi,
I´ve been trying to improve data transmission from an nRF91 dev board through nb-iot to Azure IOT-hub and always got a socket disconnection event when I tried to send...
I would like to configure the TXD, RXD, RTS and CTS pins for the UART on the nRF52832.
I saw that the uart0 node ( nordic,nrf-uarte ) has attributes like rts-pin but they...
I got an nRF52 DK, took it from the box, plugged it into USB and turned it on. One LED was flashing softly and slowly.
Then I ran nrfjprog.exe --deviceversion --log and...
Hello, two related questions:
1) We're hiring a third party, Fortify to statically analyze our code base. I'm having trouble figuring out where I can modify the build tool...
Hi,
I already have a product which is running on NRF52810 (SDK S112)
Since the lack of CPU worldwide problem i found a stock of NRF52811.
I saw it's hardware is pin...
